Search found 26 matches
- Wed Apr 23, 2008 5:13 pm
- Forum: General, New users, Purchasing
- Topic: Need a little help (MAP and TPS won't stay still)
- Replies: 4
- Views: 232
From reading some other posts it is sounding like my Vref is not getting a clean signal. The problem I have is I don't have access to a scope. How would a go about checking the Vref signal. The thread also mentioned instability in the +5v on the board. Again how would I check that. The only testing ...
- Wed Apr 23, 2008 1:22 pm
- Forum: General, New users, Purchasing
- Topic: Need a little help (MAP and TPS won't stay still)
- Replies: 4
- Views: 232
Thanks Matt. Wish they found out what caused it. I am thinking of separating the power to MS and the power to the coil. Right now they are wired up so the coil draws its power from the same place as MS. I don't think that is a problem because the datalog doesn't show a drop in voltage. Seems to me t...
- Tue Apr 22, 2008 7:30 pm
- Forum: General, New users, Purchasing
- Topic: Need a little help (MAP and TPS won't stay still)
- Replies: 4
- Views: 232
- Mon Apr 21, 2008 9:30 pm
- Forum: General, New users, Purchasing
- Topic: Need a little help (MAP and TPS won't stay still)
- Replies: 4
- Views: 232
Need a little help (MAP and TPS won't stay still)
MSI-E 029y V3.0 Installed on a Toyota 6MGE. Using 24-2 cam wheel with a Ford coil pack. The issue is this. When looking at MT while the engine is idling the MAP and TPS values are somewhat steady. While I am driving the MAP and TPS will fluctuate while at a constant speed on a level road. I thought ...
- Thu Apr 17, 2008 6:22 pm
- Forum: MS1/Extra support
- Topic: Help With Starting and Idling (Toyota 6MGE)
- Replies: 8
- Views: 531
- Tue Apr 15, 2008 7:58 pm
- Forum: MS1/Extra support
- Topic: Help With Starting and Idling (Toyota 6MGE)
- Replies: 8
- Views: 531
Still absolutely nothing from the engine. I took the spark plugs out again and they smell like fuel and they were not wet to the touch. I ziptied the ends of them together (1-6, 2-5, 3-4) and set them on top of the engine and turned the engine over. There was a delay from when I started to turn the ...
- Tue Apr 15, 2008 5:20 pm
- Forum: MS1/Extra support
- Topic: Help With Starting and Idling (Toyota 6MGE)
- Replies: 8
- Views: 531
Got new copper core spark plugs and put them in. I am getting nothing. The engine just cranks and there are no signs of life. I am getting spark according to the timing light, the plugs smell of fuel but are not dripping wet and I didn't have any compression issues before the install. There are no r...
- Mon Apr 14, 2008 8:47 pm
- Forum: MS1/Extra support
- Topic: Help With Starting and Idling (Toyota 6MGE)
- Replies: 8
- Views: 531
- Mon Apr 14, 2008 10:00 am
- Forum: MS1/Extra support
- Topic: launch control circuit
- Replies: 4
- Views: 331
- Mon Apr 14, 2008 6:36 am
- Forum: MS1/Extra support
- Topic: Help With Starting and Idling (Toyota 6MGE)
- Replies: 8
- Views: 531
- Sun Apr 13, 2008 9:02 pm
- Forum: MS1/Extra support
- Topic: Help With Starting and Idling (Toyota 6MGE)
- Replies: 8
- Views: 531
Help With Starting and Idling (Toyota 6MGE)
Background: Just converted to MSI-E 029y4 V3.0 1985 Toyota Supra 6MGE 3.0L I-6 NA 24-2 cam wheel Ford wasted spark ignition. Using a engine harness built by myself. Description I got the car running this morning. It ran rough but It did idle until it got warmed up. I then started messing with hyster...
- Wed Jan 30, 2008 10:43 pm
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: Tach Output problem
- Replies: 12
- Views: 699
How do the jumpers on the MSII board look?
I think you need to have some jumpers on the MSII board to use JS11. I tried to look through the manual but couldn't find it.
*edit* nevermind I found it it's for JS7 (found here)
http://www.msextra.com/ms2extra/MS2-Ext ... spareports
I think you need to have some jumpers on the MSII board to use JS11. I tried to look through the manual but couldn't find it.
*edit* nevermind I found it it's for JS7 (found here)
http://www.msextra.com/ms2extra/MS2-Ext ... spareports
- Sat Dec 08, 2007 12:52 am
- Forum: Megatune (obsolete)
- Topic: ShellExecute error code 31?
- Replies: 0
- Views: 395
ShellExecute error code 31?
When ever I open a saved .msq file I get a message saying that one warning was written to the audit log. When I open the audit log it tels me there is a ShellExecute error code 31. What does this mean and would it prevent MS from operating correctly.
- Fri Dec 07, 2007 8:09 pm
- Forum: General, New users, Purchasing
- Topic: Setting up an initial ignition timing table
- Replies: 120
- Views: 190582
- Thu Dec 06, 2007 12:38 pm
- Forum: General, New users, Purchasing
- Topic: Launch Control input circuit help
- Replies: 11
- Views: 1500
Are those diodes necessary? My clutch switch has a 12v pull-up on it for the factory anti-theft and cruise control. So I just spliced into it and it does have 12v with the switch closed and 0v with the switch open. I'm just JS11 and not JS7 though. The output says it's PEO. I don't even see any ref...
- Tue Dec 04, 2007 11:09 pm
- Forum: General, New users, Purchasing
- Topic: Unable to load code to the MSII chip
- Replies: 1
- Views: 373
- Tue Dec 04, 2007 8:19 pm
- Forum: General, New users, Purchasing
- Topic: Unable to load code to the MSII chip
- Replies: 1
- Views: 373
Unable to load code to the MSII chip
I tried to load the MSII code to the chip and got some wierd message. I have verified that I can get letters to appear on hyperterm when pins 12 an 13 are shorted together. I have good voltage. I am running windows 98se on an old slow pentop computer. MSII V3. I got the files from here: http://www.m...
- Mon Nov 26, 2007 7:51 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: Assembly questons for wasted spark and saab ICV (MSII v3.0)
- Replies: 4
- Views: 424
- Thu Nov 22, 2007 10:32 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: Assembly questons for wasted spark and saab ICV (MSII v3.0)
- Replies: 4
- Views: 424
- Wed Nov 21, 2007 1:54 pm
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: Assembly questons for wasted spark and saab ICV (MSII v3.0)
- Replies: 4
- Views: 424
I think I answered one of my questions For the ICV. If I want to use the FIdle output I need to have that circuit. Looking at this, http://www.megamanual.com/ms2/megasquirt_ShemV3.00.pdf (page 5), it looks like I can leave out R57 and R43. The new schematic in the link in the first post has pin 3 on...