Megasquirt Support Forum (MSEXTRA)

I am using table switching Patrol and LPG. The are some tricks to connect the thermo sensor to the ground for LPG by hardware. Who can help me to do this by software. I need some support where to change and which signals

Verstuurd vanaf mijn S30 met Tapatalk

racingmini_mtl wrote:I think there are issues with cygwin64. You need to use the 32-bit version. I know that's what I'm using and it works. And there are posts from last year that say the same thing.

Jean

@jean, 32 bit version is working without problemen. Thanks

Verstuurd vanaf mijn Nexus 10 met Tapatalk

See the third post here: http://www.msextra.com/forums/viewtopic.php?f=91&t=43601#p308151 James The upload went well. The tar created the directory d:/usr/.... In the usr/bin the are a lot of variations of m68hc11-elf-....... But the file I expected m68hc11-elf-gcc has the extention .exe and th...

See the third post here: http://www.msextra.com/forums/viewtopic.php?f=91&t=43601#p308151 James The upload went well. The tar created the directory d:/usr/.... In the usr/bin the are a lot of variations of m68hc11-elf-....... But the file I expected m68hc11-elf-gcc has the extention .exe and th...

jsmcortina wrote:Sounds like you didn't install the toolchain.

James

Can you give me soms hints to installatie the toolchain. I can not find it in the setup from the cygwin. The site www.gnu... is not accessable.


Verstuurd vanaf mijn Nexus 10 met Tapatalk

I am using the makefile for the ms2 extra but got the massage the file "...../m68hc11-elf-gcc : no such file ..". Without Google I can not found this file. Who can help me to get this file.


Verstuurd vanaf mijn Nexus 10 met Tapatalk

You can use Ohm's Law to calculate the current, but if you are not using an oscilloscope, you will also need to take duty cycle into account. Hi Matt, I am using a scope. See picture IMG_20160908_195954.jpg . The Blue line is from 3 injectors parallel 1.9 ohm. Approx 350 mv , results into 7 amps. S...

To check the actual amperage for each bank I am measuring the Voltage over R37 and R 38. Is that a valid way to define the current? In the 3.57 Board is mounted for Q1 and 2 FQPF30N06 are these Protectors for a over current? I am also using PWM for the injector control. Verstuurd vanaf mijn Nexus 10...

Hi Phil,

Thanks for your reply
Is there a manual how to create markers in the log files.
This will be a function in TunerStudio I suppose.

At the moment I try to solve a sync error code 2. This error pops up in the data log file "Sync error reason". During a data log I am also creating a tooth log-file (log-files at the same time). What I have noticed is the time stamp is not the same in de logfiles. Is there a way to synchro...

I am fighting with the same problem. Is there someone who can explain exactly what is causing this error. If an additional teeth is created by noise I was expecting error 3. "too manny teeth etc" The message mentioned "... at wrong time" what is calculated. Please help me to find...

Hello James,

I understand this issue will put on your todo list.
When do think this solution will be integrated in a release?
I am interessed in this fix, because I have an odd-fire engine.

Regards

Otto

With release 2.1 MS2 extra I could select "hardware" for the table switching function.
With release 3.1 MS2 I can only select remote port wit a bit number. Is this function only available for the CAN-bus.

Regards
Otto

Herwith the MSQ and the comm.log.
When I reduce the rpm to 0 there is not a communication error and I can change the temp etc with the simulator. After increasing the rpm --> communication gone.

Hello James, I am nog 100% sure. But I suppose when I have downloaded the firmware I have the deafult setup, which should be not a problem. The only two parameters which I have changed (no import) are the amount of cyl (8-->6) and the Even --> Odd. I have tried to activate the miniterm and switch of...

I have tested the same configuration as Karl did. Odd fire V6 engine (Citroen SM) with the stock 20090327 beta of ms2/extra 2.1.0. The only difference that I am using the basic trigger instead of the 36-1. After a second the communication is gone. The communication will start agian after a cold down...

To be sure what is called the even trigger wheel.
Is that the 36-1 or the trigger wheel with the odd-fire patron? or....

James, I have noticed a short paragraph http://www.msextra.com/ms2extra/MS2-Extra_Ignition.htm#oddfire There is mentioned a "single trigger". With this trigger is meant "odd-fire" trigger wheel on the cam-shaft or ..... Does that means a second trigger on the crank-shaft has no u...

James, Can you help me to find out which configuration is working for fuel and ignition for MS2-extra (already bought). Is it possible to adapt the code so it is working for odd-fire? My preferences step one, is fuel and ignition with distriburtion by the rotor. (or as simple as possible with a good...

Will there be a performance difference if you are using a trigger with dizzy or the 36-1 (when it is working).
With others words, is it usefull to check your remark "probably"?

Otto