hey prof
this was the map you gave me i have just played around with it a bit a s differ fuel etc
yeh i am using the std iacv woops
toomy
Search found 49 matches
- Mon Sep 05, 2011 10:09 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: first start take ages to fire ???/
- Replies: 3
- Views: 260
- Sun Sep 04, 2011 2:22 pm
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: first start take ages to fire ???/
- Replies: 3
- Views: 260
first start take ages to fire ???/
first time i go to fire the car it takes about 2 mins to get the thing going .... smell fuel too
files attached
thanks for any input
ms2 v3 running wasted spk
vw 2l 16v abf engine
files attached
thanks for any input
ms2 v3 running wasted spk
vw 2l 16v abf engine
- Sun Sep 04, 2011 3:53 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: all was working and now no crank pulse...
- Replies: 3
- Views: 306
Re: all was working and now no crank pulse...
this happened to me yesterday
had nothing fuel pump would prime but no rpm or spk etc
uploaded new firmware - re flashed ecu as guide and all works great
look at the latest firmware 3.1.0 iirc and load that then load your map etc
had nothing fuel pump would prime but no rpm or spk etc
uploaded new firmware - re flashed ecu as guide and all works great
look at the latest firmware 3.1.0 iirc and load that then load your map etc
- Mon Mar 14, 2011 1:36 pm
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: How many engines running on MS2/Extra
- Replies: 420
- Views: 220327
Re: How many engines running on MS2/Extra
Ms2 v3 running vw 2.0 60-2 with vr pick up ford coil pack
plans 636 itbs
plans 636 itbs
- Mon Oct 11, 2010 1:37 pm
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: takes 5-6 cycles before it fires?
- Replies: 2
- Views: 236
takes 5-6 cycles before it fires?
hi just finshing off a abf in a golf running great just finshed tuning and am very happy with it all
BUT
when i go to start the car it takes a good few cylcles before it fires ? when its hot its fine
do i just adjust cranking pw ? if so will this alter my ve table at all ?
tommy
BUT
when i go to start the car it takes a good few cylcles before it fires ? when its hot its fine
do i just adjust cranking pw ? if so will this alter my ve table at all ?
tommy
- Tue Sep 28, 2010 11:46 pm
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: hard cut rev limit>>>>
- Replies: 2
- Views: 411
Re: hard cut rev limit>>>>
sorry i thought it was related . sorry
i am using 2.1.0 d the latest as just reflashed it this week . ms2 v3
i am using 2.1.0 d the latest as just reflashed it this week . ms2 v3
- Tue Sep 28, 2010 12:34 pm
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: hard cut rev limit>>>>
- Replies: 2
- Views: 411
hard cut rev limit>>>>
hey guys i had a hard cut rev limit on my last ms2 on my escort and it sounded like a rally car when hits the limit like gun shots flames and bangs
now i have set up my vw g olf just tuned afrs etc and went to set to hard cut ...and it seems laim like its the soft cut ? any ideas
now i have set up my vw g olf just tuned afrs etc and went to set to hard cut ...and it seems laim like its the soft cut ? any ideas
- Sat Sep 25, 2010 12:48 pm
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: car did run but new problem
- Replies: 6
- Views: 456
Re: car did run but new problem
GOT IT GUYS .....CARS RUNNING GREAT
THANKS EVERYONE THE SUPPORT
TOMMY
THANKS EVERYONE THE SUPPORT
TOMMY
- Fri Sep 24, 2010 11:16 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: car did run but new problem
- Replies: 6
- Views: 456
Re: car did run but new problem
thanks thomas ....
i will try that tommorow morning as i stay about half hour away from my workshop ...i will update tomor and tell you how i got on !
thanks again
tommy
i will try that tommorow morning as i stay about half hour away from my workshop ...i will update tomor and tell you how i got on !
thanks again
tommy
- Fri Sep 24, 2010 10:33 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: car did run but new problem
- Replies: 6
- Views: 456
Re: car did run but new problem
will it still comunicate in boot mode as it wont comunicate with the ms at all it says that its off line?
thanks for the reply
tommy
thanks for the reply
tommy
- Fri Sep 24, 2010 9:45 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: car did run but new problem
- Replies: 6
- Views: 456
car did run but new problem
after james advised me that the vr wires were wrong way i corrected that and it fired up straight away ....i blipt the throttle and it reved great as the revs returned they went too low the car cut out BUT the fuel pump stayed on constant and the middle led is always on ? every time i turn on the ig...
- Fri Sep 24, 2010 6:10 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: non start ... weid tooth trigger log
- Replies: 11
- Views: 395
Re: non start ... weid tooth trigger log
nice one james ...thanks it was just too simple thats why i asked again
i will try the vr wiring .... anything else to check while i am there ..... i also re-calibrated tps as thats showing -2 on closed
can you think of anything else
was there a problem at all with 2.1.0p?
i will try the vr wiring .... anything else to check while i am there ..... i also re-calibrated tps as thats showing -2 on closed
can you think of anything else
was there a problem at all with 2.1.0p?
- Fri Sep 24, 2010 5:39 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: non start ... weid tooth trigger log
- Replies: 11
- Views: 395
Re: non start ... weid tooth trigger log
is that it that simple ?
i do that every time i turn off the battery isolator swith ....is this it re booted ?
i do that every time i turn off the battery isolator swith ....is this it re booted ?
- Fri Sep 24, 2010 5:31 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: non start ... weid tooth trigger log
- Replies: 11
- Views: 395
Re: non start ... weid tooth trigger log
ok should i just flash the newest firmwere at the same time ?
is this how i reboot ?
i know the jumper is on the board just unsure how to go about rebooting ?
thanks james
tommy
is this how i reboot ?
i know the jumper is on the board just unsure how to go about rebooting ?
thanks james
tommy
- Fri Sep 24, 2010 4:59 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: non start ... weid tooth trigger log
- Replies: 11
- Views: 395
Re: non start ... weid tooth trigger log
cool i will try that in a hour when i get to the unit !
james also i was changing from 36-1ford setup to 60-2 vw do i need to re boot the ms ?
could this be a prob?
james also i was changing from 36-1ford setup to 60-2 vw do i need to re boot the ms ?
could this be a prob?
- Fri Sep 24, 2010 4:26 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: non start ... weid tooth trigger log
- Replies: 11
- Views: 395
Re: non start ... weid tooth trigger log
here you go james..
- Fri Sep 24, 2010 4:10 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: non start ... weid tooth trigger log
- Replies: 11
- Views: 395
- Fri Sep 24, 2010 4:09 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: non start ... weid tooth trigger log
- Replies: 11
- Views: 395
non start ... weid tooth trigger log
hey guys i am using ms2v3 extra 2.1.0p car is a vw abf std 60-2 wheel using a vr pick up from a vr6 the car tries to fire but wont run ...i suspect it to the trigger pattern the rpm fluctuates between 0 -350 rpm on cranking i remember someone else had this and resolved by updating firmwere but not s...
- Sat Sep 18, 2010 2:51 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: OEM 36-1 Trigger Wheel !!
- Replies: 10
- Views: 719
Re: OEM 36-1 Trigger Wheel !!
would you not be quicker just buying a trigger wheel ?36-1 come in all differ sizes to suit your application
tommy
tommy
- Fri Sep 17, 2010 12:37 am
- Forum: MS2/Extra, MS2, Microsquirt and Microsquirt module support
- Topic: fried 921?
- Replies: 14
- Views: 792
Re: fried 921?
its cool guys got it
phill sent me a bip373 to replace Q16 and all is good
thanks for the input
tommy
phill sent me a bip373 to replace Q16 and all is good
thanks for the input
tommy