Megasquirt MSEXTRA / MS3EFI

Support and discussion forum for Megasquirt 1, 2, 3, Microsquirt/module & DIYPNP

MegaSquirt Forums: MSefi, MSextra, MS Success Stories, MS User Groups, MicroSquirt, MSgpio

Quick links: Manuals : Megasquirt info : Forum help page : Downloads

logging Barometer reading

Questions specific to Megalogviewer

Moderator: LT401Vette

Post a reply

logging Barometer reading

Postby GraemeD » Wed May 30, 2012 1:28 pm

noob question here,
How do I graph "baro"? I have a seperate baro sensor and I would like to be able to see it, as I live in Colorado and can gain/loos lots of altitude in a single drive.
'94 Miata ; 2001 VVT engine; DIYPnP, 3.3.B13; sequential injection Board; PWM IAC converter Board; VVTuner; 99-00 crank & cam sensors; sequential Toyota COP ignition; LC-1 wide band O2; Square Top manifold; RB header; Custom CAI.
GraemeD
Helpful MS/Extra'er
 
Posts: 62
Joined: Sun Mar 27, 2011 6:10 pm
Location: Colorado, USA
Top

Re: logging Barometer reading

Postby LT401Vette » Wed May 30, 2012 1:32 pm

It will likely take a custom ini with TunerStudio.

What firmware are you using?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
User avatar
LT401Vette
Super MS/Extra'er
 
Posts: 6880
Joined: Sat Jul 16, 2005 8:07 am
Location: Charlotte, NC
Top

Re: logging Barometer reading

Postby GraemeD » Wed May 30, 2012 1:40 pm

MSextra2 3.2.2 beta

2012-05-30_10.30.37.msq
(83.4 KiB) Downloaded 25 times
'94 Miata ; 2001 VVT engine; DIYPnP, 3.3.B13; sequential injection Board; PWM IAC converter Board; VVTuner; 99-00 crank & cam sensors; sequential Toyota COP ignition; LC-1 wide band O2; Square Top manifold; RB header; Custom CAI.
GraemeD
Helpful MS/Extra'er
 
Posts: 62
Joined: Sun Mar 27, 2011 6:10 pm
Location: Colorado, USA
Top

Re: logging Barometer reading

Postby LT401Vette » Wed May 30, 2012 1:48 pm

So if you just want to data log the barometer value that is displayed on the gauge, you need to add this to a custom.ini file:

Code: Select all

[Datalog]
   ;       Channel          Label          Type    Format
   ;       --------------   ----------     -----   ------

   entry = barometer,      "Barometer",         float,  "%.1f"


I did it in the attached.

So now place this attached file in the dir:
[YourTunerStudioProjectDir]/projectCfg/

Make sure to rename it to custom.ini
Attachments
custom_baro.ini
Rename to custom.ini for TS to find it.
(190 Bytes) Downloaded 28 times
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
User avatar
LT401Vette
Super MS/Extra'er
 
Posts: 6880
Joined: Sat Jul 16, 2005 8:07 am
Location: Charlotte, NC
Top

Re: logging Barometer reading

Postby GraemeD » Wed May 30, 2012 2:08 pm

Thanks,
I appreciate all the help

Graeme
Golden, CO
'94 Miata ; 2001 VVT engine; DIYPnP, 3.3.B13; sequential injection Board; PWM IAC converter Board; VVTuner; 99-00 crank & cam sensors; sequential Toyota COP ignition; LC-1 wide band O2; Square Top manifold; RB header; Custom CAI.
GraemeD
Helpful MS/Extra'er
 
Posts: 62
Joined: Sun Mar 27, 2011 6:10 pm
Location: Colorado, USA
Top
Post a reply

Return to Megalogviewer

Who is online

Users browsing this forum: No registered users and 1 guest

Powered by phpBB® Forum Software © phpBB Group