logging Barometer reading

Questions specific to Megalogviewer

Moderator: LT401Vette

logging Barometer reading

Postby GraemeD » Wed May 30, 2012 1:28 pm

noob question here,
How do I graph "baro"? I have a seperate baro sensor and I would like to be able to see it, as I live in Colorado and can gain/loos lots of altitude in a single drive.
'94 Miata ; 2001 VVT engine; DIYPnP, 3.3.0; sequential injection Board; PWM IAC converter Board; VVTuner; 99-00 crank & cam sensors; sequential Toyota COP ignition; LC-1 wide band O2; Square Top manifold; RB header; Custom CAI.
GraemeD
Helpful MS/Extra'er
 
Posts: 67
Joined: Sun Mar 27, 2011 6:10 pm
Location: Colorado, USA

Re: logging Barometer reading

Postby LT401Vette » Wed May 30, 2012 1:32 pm

It will likely take a custom ini with TunerStudio.

What firmware are you using?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
User avatar
LT401Vette
Super MS/Extra'er
 
Posts: 8381
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC

Re: logging Barometer reading

Postby GraemeD » Wed May 30, 2012 1:40 pm

MSextra2 3.2.2 beta

2012-05-30_10.30.37.msq
'94 Miata ; 2001 VVT engine; DIYPnP, 3.3.0; sequential injection Board; PWM IAC converter Board; VVTuner; 99-00 crank & cam sensors; sequential Toyota COP ignition; LC-1 wide band O2; Square Top manifold; RB header; Custom CAI.
GraemeD
Helpful MS/Extra'er
 
Posts: 67
Joined: Sun Mar 27, 2011 6:10 pm
Location: Colorado, USA

Re: logging Barometer reading

Postby LT401Vette » Wed May 30, 2012 1:48 pm

So if you just want to data log the barometer value that is displayed on the gauge, you need to add this to a custom.ini file:

Code: Select all

[Datalog]
   ;       Channel          Label          Type    Format
   ;       --------------   ----------     -----   ------

   entry = barometer,      "Barometer",         float,  "%.1f"


I did it in the attached.

So now place this attached file in the dir:
[YourTunerStudioProjectDir]/projectCfg/

Make sure to rename it to custom.ini
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
User avatar
LT401Vette
Super MS/Extra'er
 
Posts: 8381
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC

Re: logging Barometer reading

Postby GraemeD » Wed May 30, 2012 2:08 pm

Thanks,
I appreciate all the help

Graeme
Golden, CO
'94 Miata ; 2001 VVT engine; DIYPnP, 3.3.0; sequential injection Board; PWM IAC converter Board; VVTuner; 99-00 crank & cam sensors; sequential Toyota COP ignition; LC-1 wide band O2; Square Top manifold; RB header; Custom CAI.
GraemeD
Helpful MS/Extra'er
 
Posts: 67
Joined: Sun Mar 27, 2011 6:10 pm
Location: Colorado, USA


Return to Megalogviewer

Who is online

Users browsing this forum: No registered users and 1 guest