Pointer/Tail on VE and Timing tables MIA

Questions specific to Megalogviewer

Moderator: LT401Vette

Post Reply
corvelton
MS/Extra Newbie
Posts: 4
Joined: Wed Jul 29, 2015 9:54 am

Pointer/Tail on VE and Timing tables MIA

Post by corvelton »

So i recently supercharged my car and expanded my VE and timing tables on it up to where i think the limits are gonna be for the blower. I drove around and logged a few min of casual driving along with one WOT pull and i went to my logs and found it logged the run, But i have no pointer on the VE table or Timing table. Is there a hotkey to turn it on/off that i accidentally hit? I cant find a on/off option for the pointer anywhere. Thanks in advance.
LT401Vette
Super MS/Extra'er
Posts: 12697
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC
Contact:

Re: Pointer/Tail on VE and Timing tables MIA

Post by LT401Vette »

No, it should always be there if the engine is running..

What version TunerStudio?
What firmware?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
corvelton
MS/Extra Newbie
Posts: 4
Joined: Wed Jul 29, 2015 9:54 am

Re: Pointer/Tail on VE and Timing tables MIA

Post by corvelton »

TS version V2.6.14 , MSX firmware # 3.3.3
LT401Vette
Super MS/Extra'er
Posts: 12697
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC
Contact:

Re: Pointer/Tail on VE and Timing tables MIA

Post by LT401Vette »

Check what your Default Y-Axis Field is set to under:
Options --> Default Y-Axis Field

Also check if there is a Y-Axis over-ride set.
Right click on the Y Axis of the table.
If it says "Clear Y-Axis Override", select it.

If it says "Set Y-Axis Override" then there is no override set.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
corvelton
MS/Extra Newbie
Posts: 4
Joined: Wed Jul 29, 2015 9:54 am

Re: Pointer/Tail on VE and Timing tables MIA

Post by corvelton »

LT401Vette wrote:Check what your Default Y-Axis Field is set to under:
Options --> Default Y-Axis Field

Also check if there is a Y-Axis over-ride set.
Right click on the Y Axis of the table.
If it says "Clear Y-Axis Override", select it.

If it says "Set Y-Axis Override" then there is no override set.
The Y Axis is set to MAP and there is no Y axis set, "Set Y-Axis Override"
corvelton
MS/Extra Newbie
Posts: 4
Joined: Wed Jul 29, 2015 9:54 am

Re: Pointer/Tail on VE and Timing tables MIA

Post by corvelton »

I turned Y Axis Override on to 185 (My max KPA) and its working again! :D Whats the point of the override?
LT401Vette
Super MS/Extra'er
Posts: 12697
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC
Contact:

Re: Pointer/Tail on VE and Timing tables MIA

Post by LT401Vette »

It should be set to a number... That should be set to the log field name that the Y Axis tracks to.
So for standard Speed Density the default Y Axis would be set to MAP.
There would be no Y-Axis override.

However, if you have another table that uses a different Y Axis field, you would set the Y-Axis Override to the correct tracking field name for that table.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Post Reply