Pointer/Tail on VE and Timing tables MIA
Moderator: LT401Vette
Pointer/Tail on VE and Timing tables MIA
So i recently supercharged my car and expanded my VE and timing tables on it up to where i think the limits are gonna be for the blower. I drove around and logged a few min of casual driving along with one WOT pull and i went to my logs and found it logged the run, But i have no pointer on the VE table or Timing table. Is there a hotkey to turn it on/off that i accidentally hit? I cant find a on/off option for the pointer anywhere. Thanks in advance.
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Pointer/Tail on VE and Timing tables MIA
No, it should always be there if the engine is running..
What version TunerStudio?
What firmware?
What version TunerStudio?
What firmware?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Re: Pointer/Tail on VE and Timing tables MIA
TS version V2.6.14 , MSX firmware # 3.3.3
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Pointer/Tail on VE and Timing tables MIA
Check what your Default Y-Axis Field is set to under:
Options --> Default Y-Axis Field
Also check if there is a Y-Axis over-ride set.
Right click on the Y Axis of the table.
If it says "Clear Y-Axis Override", select it.
If it says "Set Y-Axis Override" then there is no override set.
Options --> Default Y-Axis Field
Also check if there is a Y-Axis over-ride set.
Right click on the Y Axis of the table.
If it says "Clear Y-Axis Override", select it.
If it says "Set Y-Axis Override" then there is no override set.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Re: Pointer/Tail on VE and Timing tables MIA
The Y Axis is set to MAP and there is no Y axis set, "Set Y-Axis Override"LT401Vette wrote:Check what your Default Y-Axis Field is set to under:
Options --> Default Y-Axis Field
Also check if there is a Y-Axis over-ride set.
Right click on the Y Axis of the table.
If it says "Clear Y-Axis Override", select it.
If it says "Set Y-Axis Override" then there is no override set.
Re: Pointer/Tail on VE and Timing tables MIA
I turned Y Axis Override on to 185 (My max KPA) and its working again! Whats the point of the override?
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Pointer/Tail on VE and Timing tables MIA
It should be set to a number... That should be set to the log field name that the Y Axis tracks to.
So for standard Speed Density the default Y Axis would be set to MAP.
There would be no Y-Axis override.
However, if you have another table that uses a different Y Axis field, you would set the Y-Axis Override to the correct tracking field name for that table.
So for standard Speed Density the default Y Axis would be set to MAP.
There would be no Y-Axis override.
However, if you have another table that uses a different Y Axis field, you would set the Y-Axis Override to the correct tracking field name for that table.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html