Hi Team,
I am running new pre-assembled MS2 V3.57 from DIY Autotune, with HEI mod. I am about to install it on a straight 6 running HEI distributor and 7 pin GM module & single coil. I was hoping someone here could take a look at my ignition settings to ensure they look right before I try on the car, as msextra code makes tuner studio look a bit different to some of the other screenshots I have seen on the net.
Appreciate the help.
Regards Jacob
Settings for 7 Pin HEI V2.6.19
Moderators: jsmcortina, muythaibxr
-
- MS/Extra Newbie
- Posts: 5
- Joined: Wed May 04, 2016 5:47 am
-
- Site Admin
- Posts: 39621
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Settings for 7 Pin HEI V2.6.19
I moved the topic as this is unrelated to TunerStudio.
Please read the MS2V357 Hardware Manual from the "manuals" link above. It covers wiring and settings for HEI7.
James
Please read the MS2V357 Hardware Manual from the "manuals" link above. It covers wiring and settings for HEI7.
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- MS/Extra Newbie
- Posts: 5
- Joined: Wed May 04, 2016 5:47 am
Re: Settings for 7 Pin HEI V2.6.19
Thanks James, I found the HEI7 information you referred to (sorry about initial post location).
I am still a little confused though, an article I read by DIY Autotune mentioned setting spark output to "Going High (Inverted)" however I dont have this option, and it does not seem to be the default setting as recommended by the manual?
https://www.diyautotune.com/support/tec ... efi/part2/
from the manual: Many thanks,
Jacob
I am still a little confused though, an article I read by DIY Autotune mentioned setting spark output to "Going High (Inverted)" however I dont have this option, and it does not seem to be the default setting as recommended by the manual?
https://www.diyautotune.com/support/tec ... efi/part2/
from the manual: Many thanks,
Jacob
-
- Site Admin
- Posts: 39621
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Settings for 7 Pin HEI V2.6.19
Read one set of instructions only.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Master MS/Extra'er
- Posts: 789
- Joined: Sun May 02, 2004 5:55 pm
- Location: Cleveland, Ohio
- Contact:
Re: Settings for 7 Pin HEI V2.6.19
On my HEI setup (8pin on a V8), I have spark output set to "Going Low", and I also have Ignition Input Capture to "Rising Edge". I think I'm running Extra 3.3.2.
-Dave
-Dave
'70 Chevelle ZZ383/700r4/3.73 MS3X, 36-1, LS Coils, Holley Stealthram -- success story
'92 Saturn 1.9 DOHC/5sp, MS3, Champcar racer success story
'79 Malibu DartSHP400/80mm/PG/3.55, MS3X/36-1/LS Coils -- success story
Porsche 944 S2 3.0 -- MS3X/36-1/LS Coils, 1:44s Mid-Ohio, Pro Course
'92 Saturn 1.9 DOHC/5sp, MS3, Champcar racer success story
'79 Malibu DartSHP400/80mm/PG/3.55, MS3X/36-1/LS Coils -- success story
Porsche 944 S2 3.0 -- MS3X/36-1/LS Coils, 1:44s Mid-Ohio, Pro Course
-
- MS/Extra Newbie
- Posts: 5
- Joined: Wed May 04, 2016 5:47 am
Re: Settings for 7 Pin HEI V2.6.19
Thanks Dave - appreciate the help.
Regards Jacob
Regards Jacob