MS2 AFR TARGET FAIL
Moderators: jsmcortina, muythaibxr
-
- Helpful MS/Extra'er
- Posts: 35
- Joined: Sun Feb 14, 2016 5:14 pm
MS2 AFR TARGET FAIL
HI, i have fail in the afr target, always is un 14.0. and tune analyze live therefore it does not work well.
thanks
thanks
-
- Super MS/Extra'er
- Posts: 1986
- Joined: Sat Jul 22, 2006 8:02 pm
- Location: Eureka, NV USA
- Contact:
Re: MS2 AFR TARGET FAIL
When I try to load your MSQ it appears to be empty.
As far as your log goes, jacking the throttle 6-7 times in about 3 seconds makes it a bit difficult to visualize whats going on.
Ken
As far as your log goes, jacking the throttle 6-7 times in about 3 seconds makes it a bit difficult to visualize whats going on.
Ken
Last edited by kjones6039 on Thu Apr 13, 2017 7:32 am, edited 1 time in total.
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
-
- Super MS/Extra'er
- Posts: 1275
- Joined: Thu Apr 07, 2005 11:23 pm
- Location: Sydney, Australia
- Contact:
Re: MS2 AFR TARGET FAIL
Have you calibrated AFR table?
-
- Helpful MS/Extra'er
- Posts: 35
- Joined: Sun Feb 14, 2016 5:14 pm
Re: MS2 AFR TARGET FAIL
yes, but in the AFR TABLE 1 , i have target of 12.8 a WOT and 14.7 to idle, but el AFR1 TARGET in tune analyze live is always is 14.0, not change.
Re: MS2 AFR TARGET FAIL
You have "don't include AFR target" set?
General settings tab.
General settings tab.
Correctly identify your MS ecu here
Read the Do's and Don'ts to avoid the common pitfalls before starting your install or asking for help
Use only these manuals other manuals may cause brain damage or worse.
Read the Do's and Don'ts to avoid the common pitfalls before starting your install or asking for help
Use only these manuals other manuals may cause brain damage or worse.
-
- Super MS/Extra'er
- Posts: 1986
- Joined: Sat Jul 22, 2006 8:02 pm
- Location: Eureka, NV USA
- Contact:
Re: MS2 AFR TARGET FAIL
That'll do it!rickb794 wrote:You have "don't include AFR target" set?
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
-
- Helpful MS/Extra'er
- Posts: 35
- Joined: Sun Feb 14, 2016 5:14 pm
Re: MS2 AFR TARGET FAIL
yes, i change to "incluide AFRtarget". but the problem remains the same.
MS/Extra 3.4.2.
MS/Extra 3.4.2.
Re: MS2 AFR TARGET FAIL
After a burn and a power cycle?
Sent from my SM-G900V using Tapatalk
Sent from my SM-G900V using Tapatalk
Correctly identify your MS ecu here
Read the Do's and Don'ts to avoid the common pitfalls before starting your install or asking for help
Use only these manuals other manuals may cause brain damage or worse.
Read the Do's and Don'ts to avoid the common pitfalls before starting your install or asking for help
Use only these manuals other manuals may cause brain damage or worse.
Re: MS2 AFR TARGET FAIL
incorporate AFR target does not change what the AFR target is, it changes the fuel calculation such that changing the AFR target table will cause an immediate change in fuel for the corresponding cells rather than "simply" a change in the AFR target for that vector.
Can you screen shot this please? Turn megasquirt on with TS connected, go to fuel settings then click fuel calculations summary and screenshot that please. Also do you have a stimulator?
Can you screen shot this please? Turn megasquirt on with TS connected, go to fuel settings then click fuel calculations summary and screenshot that please. Also do you have a stimulator?
-
- Super MS/Extra'er
- Posts: 4122
- Joined: Fri May 07, 2004 3:33 am
- Location: Australia
Re: MS2 AFR TARGET FAIL
Your msq is showing EGO control as Disabled.
Find the Manuals up top under Quick links: Manuals.
Cheers Luke
Cheers Luke
-
- Helpful MS/Extra'er
- Posts: 35
- Joined: Sun Feb 14, 2016 5:14 pm
Re: MS2 AFR TARGET FAIL
this is the problem, with afr target when the engine is run.
Re: MS2 AFR TARGET FAIL
I'm surprised but I think it's because EGO control is disabled. The 14.0 value is hard-coded in the MSQ, however it's hard-coded in mine too and my AFR Target works but I always have EGO control turned on. If I don't want EGO control to do anything I set step size to 0.
Make the changes yourself or you can try MSQ attached.
Make the changes yourself or you can try MSQ attached.
Re: MS2 AFR TARGET FAIL
In the MSQ posted previously the EGO is disabled.
The MS has no idea what the exhaust looks like how can it make corrections?
Do you have a wideband installed?
Have you calibrated the sensor? Under the "tools" drop down menu, "Calibrate AFR Table"?
Please use screen captures rather than cell phone pics, to make things readable.
The MS has no idea what the exhaust looks like how can it make corrections?
Do you have a wideband installed?
Have you calibrated the sensor? Under the "tools" drop down menu, "Calibrate AFR Table"?
Please use screen captures rather than cell phone pics, to make things readable.
Correctly identify your MS ecu here
Read the Do's and Don'ts to avoid the common pitfalls before starting your install or asking for help
Use only these manuals other manuals may cause brain damage or worse.
Read the Do's and Don'ts to avoid the common pitfalls before starting your install or asking for help
Use only these manuals other manuals may cause brain damage or worse.
-
- Helpful MS/Extra'er
- Posts: 35
- Joined: Sun Feb 14, 2016 5:14 pm
Re: MS2 AFR TARGET FAIL
seijirou wrote:I'm surprised but I think it's because EGO control is disabled. The 14.0 value is hard-coded in the MSQ, however it's hard-coded in mine too and my AFR Target works but I always have EGO control turned on. If I don't want EGO control to do anything I set step size to 0.
Make the changes yourself or you can try MSQ attached.
thanks, work well.