Presuming this is an OK forum to ask, the title says it all.
Thanks in advance,
Jim
Is there a way to get RPMdot to display and or log??
Moderator: LT401Vette
-
- Site Admin
- Posts: 39615
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Is there a way to get RPMdot to display and or log??
Depends on the firmware version and what is in the ini file. It isn't specific to the tuning software.
It is logged in the current MS2/Extra 3.0.3 alpha code, but there isn't a gauge for it. You can add a gauge by editing the ini file. (mainController.ini)
find the gauges and then add this line:
James
It is logged in the current MS2/Extra 3.0.3 alpha code, but there isn't a gauge for it. You can add a gauge by editing the ini file. (mainController.ini)
find the gauges and then add this line:
Code: Select all
rpmdot = rpmdot, "rpmdot", "rpm/sec", -15000, 15000, 65535, 65535, 65535, 65535, 0, 0
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: Is there a way to get RPMdot to display and or log??
Thanks James.
Jim
Jim
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Is there a way to get RPMdot to display and or log??
You can also create a gauge for it without going in the ini. If you go into designer mode and and create a new gauge or change an existing gauge.
If in designer mode right click on a gauge, select:
Properties --> OutputChannel
and in the dialog you can select rpmdot if you have a firmware with the OutputChannel.
If in designer mode right click on a gauge, select:
Properties --> OutputChannel
and in the dialog you can select rpmdot if you have a firmware with the OutputChannel.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Super MS/Extra'er
- Posts: 3653
- Joined: Fri Apr 02, 2004 8:40 pm
- Location: Virginia Beach, VA
- Contact:
Re: Is there a way to get RPMdot to display and or log??
At one time I wasn't able to enter a negative value for gauge limit; I can't recall how I got around it.LT401Vette wrote:You can also create a gauge for it without going in the ini. If you go into designer mode and and create a new gauge or change an existing gauge.
If in designer mode right click on a gauge, select:
Properties --> OutputChannel
and in the dialog you can select rpmdot if you have a firmware with the OutputChannel.
Peter Florance
PF Tuning
81 BMW Euro 528i ESP Car
60-2 Wheel LS2 Coils, Low Z Inj
Co-Driver 1999 BMW E46 DSP car.
PF Tuning
81 BMW Euro 528i ESP Car
60-2 Wheel LS2 Coils, Low Z Inj
Co-Driver 1999 BMW E46 DSP car.