TunerStudio MS 1.0 Released

Activate · Post by **Activate** » Mon Mar 21, 2011 1:16 pm

Update does great!!

I only still get the K version in top of the programm?

Thanks and greetings,

Erik

Post by **jsmcortina** » Mon Mar 21, 2011 1:20 pm

I guess it didn't update then..!

The release says "TunerStudio MS v1.0" in the title bar.

James

kjones6039 · Post by **kjones6039** » Mon Mar 21, 2011 1:29 pm

Win7 starter on a netbook......

I did the auto update from TS and TS wouldn't run anymore! I uninstalled and down loaded 1.0 from the TS site, reinstalled. Voila!! Up and running!!

Works great.

Ken

Activate · Post by **Activate** » Mon Mar 21, 2011 1:33 pm

It is running now!!!

dan187 · Post by **dan187** » Tue Mar 22, 2011 7:56 am

Is there a way of rolling back my install version?

I tried running the previous version setup file but the software tells me I have a newer version so it won't install.

elaw · Post by **elaw** » Tue Mar 22, 2011 9:17 am

That's weird, I did not have that experience. Downloaded the 0.999.9k setup, ran it, didn't get any errors and it seems to have worked (when I launch TS it now says 0.999.9k in the title bar). This is on Windows XP.

msegt · Post by **msegt** » Tue Mar 22, 2011 4:16 pm

first time i updated it stayed on version k, i did it again and its now 1.0 i dont know whats up with that, but it worked the second time...

Jan · Post by **Jan** » Tue Mar 22, 2011 9:30 pm

So today I upgraded to TunerStudio 1.0 to tune my friends MS1, but when I went to the VE Analyze Live tab it just sat on the loading screen. I tried closing the program and same thing happened, and I also created a new project to have the same with happen. I wasn't ever able to load VE Analyze Live and had to downgrade to 0.999.9o.

HidRo · Post by **HidRo** » Wed Mar 23, 2011 4:04 am

One thing I saw now for this new version is that you cannot open several windows, for example Ignition 1 and Ignition 3.
Now, when you have the ignition window open, you cannot check anything else until you close it.
Did you do this change on purpose?

EDIT: From what I tested so far (and not all) only the Engine Constants will alow you to open another window simultaneously.

Post by **jsmcortina** » Wed Mar 23, 2011 10:31 am

See if you have "modal" enabled.

James

HidRo · Post by **HidRo** » Wed Mar 23, 2011 12:28 pm

jsmcortina wrote:See if you have "modal" enabled.

James

~You are absolutely correct!
Not sure why that changes (if it was me, or the upgrade, but I suspect me) but now it's back again.
Thanks!

VolvoGuy50 · Post by **VolvoGuy50** » Wed Mar 23, 2011 12:51 pm

Awesome! Updating now!

LT401Vette · Post by **LT401Vette** » Fri Mar 25, 2011 10:34 pm

elaw,
if you shut of "Report INI warnings" under the menu:
Options --> Advanced

Those will go away.

Lapkritis · Post by **Lapkritis** » Mon Mar 28, 2011 12:31 pm

Running the full version 1.0 up here and works great. Thanks.

-Andrew

Huey · Post by **Huey** » Mon Mar 28, 2011 3:09 pm

dan187 wrote:Great software, good work.

However, I just updated to v1. Right before the update my temp sensors were correct, after update the software reloaded and the readings are now too low (just as if the calibration is wrong). Could you suggest a solution for me?

I've checked and the inc files are still in the project folder.

Regards
Dan

Did you find a fix for this problem? I have the same problem and my inc files are here C:\Users\Owner\Documents\TunerStudioProjects\Turbo_Buggy\inc
I looked inside the files and they look correct. I'm assuming TS just doesn't see them any more

TypeSL2 · Post by **TypeSL2** » Mon Mar 28, 2011 6:33 pm

Thanks so much man. I was finally able to run TS in 15 fps without it wigging out. Job well done.

James

LT401Vette · Post by **LT401Vette** » Mon Mar 28, 2011 8:53 pm

Huey wrote:
dan187 wrote:Great software, good work.

However, I just updated to v1. Right before the update my temp sensors were correct, after update the software reloaded and the readings are now too low (just as if the calibration is wrong). Could you suggest a solution for me?

I've checked and the inc files are still in the project folder.

Regards
Dan
Did you find a fix for this problem? I have the same problem and my inc files are here C:\Users\Owner\Documents\TunerStudioProjects\Turbo_Buggy\inc
I looked inside the files and they look correct. I'm assuming TS just doesn't see them any more

No, but I did some digging and I found a problem that started with 9m. I haven't changed anything there in at least a year and a half, so i didn't think it could be broke, but actually it is. When it does the ini validations the project dir has not yet been set, so it never finds the inc in the project and loads the app one. Then when real data comes in it has the app level once cached.

There will be a patch fix out for this tomorrow.

Huey · Post by **Huey** » Tue Mar 29, 2011 3:23 am

Okay, sounds good

Thanks

Asteris · Post by **Asteris** » Tue Mar 29, 2011 10:27 am

TS 1.001 was auto updated to my PC. Anything new?

LT401Vette · Post by **LT401Vette** » Tue Mar 29, 2011 10:35 am

It is in the change log:
http://tunerstudio.com/index.php?option ... &Itemid=61

2 fixes. Loading inc files from the project first and fixed the double pasting of gauges when using CTRL+P

Megasquirt Support Forum (MSEXTRA)

TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released

Re: TunerStudio MS 1.0 Released