Hi Phil, that took care of it you are the man.
Thanks, David
Error Mesage
Moderator: LT401Vette
-
- Super MS/Extra'er
- Posts: 1281
- Joined: Thu Aug 19, 2010 6:22 pm
- Location: White House, TN USA
Re: Error Mesage
1976 Datsun 280Z L28ET Garrett GT35R T3-T04E stage3 50 trim 63 A/R housing custom grind cam 2000-6000 rpm 440cc injectors intercooled 18 lbs. boost
3" exhaust turbo back LC-1 o2 sensor Hallman manual boost controller EDIS 6 ignition batch fire 60mm throttle body 5 spd T5 borg warner 3.54 lsd
3" exhaust turbo back LC-1 o2 sensor Hallman manual boost controller EDIS 6 ignition batch fire 60mm throttle body 5 spd T5 borg warner 3.54 lsd
-
- MS/Extra Newbie
- Posts: 16
- Joined: Mon Mar 27, 2017 12:09 am
Re: Error Mesage
This is the only thread i found while searching error message "Content is not allowed in prolog". So i decided to post my question here to keep the subject centered.
I an fiddling around with tunerstudio (Running the MS2-Extra-Example file, No MS connected).
I generated and loaded an ignition and afr table as instructed in the megamanual without issues.
I also tried the VE table generator on megamanual to create an Initial VE table for my engine. But i get this error when trying to load it into my project.
Is used the following settings:
Idle RPM is 600 RPM
Est idle vac. Is 24 Hg
RPM redline is 12000 RPM
Peak flywheel hp is 100hp @ 12000 RPM
Peal torque is 50 lbft @ 10500 RPM
Engine displacement is 0.75 L
Engine max boost is 0 psi
Next save as VEX file via notepad.
When i load it in Tunerstudio i get the "Content is not allowed in prolog" why am i getting this error with the VE table?
I an fiddling around with tunerstudio (Running the MS2-Extra-Example file, No MS connected).
I generated and loaded an ignition and afr table as instructed in the megamanual without issues.
I also tried the VE table generator on megamanual to create an Initial VE table for my engine. But i get this error when trying to load it into my project.
Is used the following settings:
Idle RPM is 600 RPM
Est idle vac. Is 24 Hg
RPM redline is 12000 RPM
Peak flywheel hp is 100hp @ 12000 RPM
Peal torque is 50 lbft @ 10500 RPM
Engine displacement is 0.75 L
Engine max boost is 0 psi
Next save as VEX file via notepad.
When i load it in Tunerstudio i get the "Content is not allowed in prolog" why am i getting this error with the VE table?
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Error Mesage
Can you post the file you are trying to load?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html