knock log SD bug?
Moderator: LT401Vette
-
- Super MS/Extra'er
- Posts: 855
- Joined: Sun Oct 10, 2010 6:33 am
knock log SD bug?
I see the difference between SD LOG an tunerstudio LOG for knock1 cyl1.
IN SD log, knock cyl1 is fix value....
configuration for lancia delta IAW.
James, I can't attach the log because is big for forum (isn't possible incrase the space at 1mb?).
I send you it, for email
thanks
IN SD log, knock cyl1 is fix value....
configuration for lancia delta IAW.
James, I can't attach the log because is big for forum (isn't possible incrase the space at 1mb?).
I send you it, for email
thanks
-
- Site Admin
- Posts: 39619
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: knock log SD bug?
Please also post or send the raw .MS3 logfile and the MSQ.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 855
- Joined: Sun Oct 10, 2010 6:33 am
Re: knock log SD bug?
Ok, tunerstudio LOG is in your mail. Is big for forum.
In tunerstudio log is correct the value knock1, but in SD I see scorrect value.
Thanks
In tunerstudio log is correct the value knock1, but in SD I see scorrect value.
Thanks
-
- Experienced MS/Extra'er
- Posts: 226
- Joined: Fri Apr 08, 2005 2:08 pm
- Location: Wathlingen, Germany
Re: knock log SD bug?
Hallo Christian
I have a similar problem with Egocor...., this help!
Please make a test.
In TS under SD Card Datalloging, Remove all (Strg+a) "Selected Datalog Fields", then make your Datalog Fields new.
Frank
I have a similar problem with Egocor...., this help!
Please make a test.
In TS under SD Card Datalloging, Remove all (Strg+a) "Selected Datalog Fields", then make your Datalog Fields new.
Frank
-
- Site Admin
- Posts: 39619
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: knock log SD bug?
This looks to be a conversion error. I'm sending a mail to Phil about it.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 855
- Joined: Sun Oct 10, 2010 6:33 am
Re: knock log SD bug?
ok thanks
-
- Super MS/Extra'er
- Posts: 855
- Joined: Sun Oct 10, 2010 6:33 am
Re: knock log SD bug?
other problem with sd card
I attach log msd and ms3 file....
You see AFR, boost duty.... and other value...
I attach log msd and ms3 file....
You see AFR, boost duty.... and other value...
-
- Site Admin
- Posts: 39619
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: knock log SD bug?
Is this still the same with the current TS beta ?
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: knock log SD bug?
There have been no changes in regard to this in the beta.
Looking through the data, it looks as though a steady xE8 was logged. So the transformations are correct.
Based on what I have seen in the past, my guess would be that perhaps one of the logged OutputChannels changed and so the length set would be wrong. This would cause the firmware to log the incorrect number of bytes and shift all fields after.
This can be verified, it is just a bit of work to map all the logged offsets back to the ini definition and find the one that doesn't match.
If this is the case, doing as franksidebike said and removing the logged SD fields and re adding them will fix it.
Looking through the data, it looks as though a steady xE8 was logged. So the transformations are correct.
Based on what I have seen in the past, my guess would be that perhaps one of the logged OutputChannels changed and so the length set would be wrong. This would cause the firmware to log the incorrect number of bytes and shift all fields after.
This can be verified, it is just a bit of work to map all the logged offsets back to the ini definition and find the one that doesn't match.
If this is the case, doing as franksidebike said and removing the logged SD fields and re adding them will fix it.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Site Admin
- Posts: 39619
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: knock log SD bug?
When I checked the log files posted the data appeared to match the size/offset headers in the .MS3 file, but it appeared to have transformed incorrectly?
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Site Admin
- Posts: 39619
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: knock log SD bug?
That isn't what I found. 0xe8 is the second byte of EGOCOR (100.0% = 0x03e8) which is the byte that proceeds knock_cyl01. The byte that should be transformed to knock_cyl01 is 0x1a.Looking through the data, it looks as though a steady xE8 was logged. So the transformations are correct.
I see a potential issue that might be confusing TS?
Offset 86 :
Code: Select all
cel_status = scalar, U16, 86, "bit", 1.000, 0.0 ; engine fault bits
cel_status_map = bits, U08, 87, [0:0] ; low byte
...
cel_status_flex = bits, U08, 86, [0:0] ; high byte
...
The MSQ has two bytes set which matches the ini file and log file.
The data all looks to be in the correct place as far as I can tell comparing the hexdump of the MS3 file and the offsets/sizes in the ini file.
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: knock log SD bug?
Yes I believe the double mapping to 2 different size fields is causing the problem.
It shouldn't be very difficult to add support for doing that.
It shouldn't be very difficult to add support for doing that.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html