pulsewidth as parameter in output port
Moderator: LT401Vette
pulsewidth as parameter in output port
Hi,
Is it correct that if I use the pulsewidth as a parameter in the output port I can only use rounded numbers? This is a bit of a problem because there is quite a difference between a pw of 2.0 and 3.0, having nothing inbetween.
Need a liilebit more resolution.
Rene
Is it correct that if I use the pulsewidth as a parameter in the output port I can only use rounded numbers? This is a bit of a problem because there is quite a difference between a pw of 2.0 and 3.0, having nothing inbetween.
Need a liilebit more resolution.
Rene
Rover Vitesse 3.5
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor
-
- Super MS/Extra'er
- Posts: 9130
- Joined: Sun May 02, 2004 6:51 am
- Location: Quebec, Canada
- Contact:
Re: pulsewidth as parameter in output port
That would actually be a TunerStudio issue.
Jean
Jean
Re: pulsewidth as parameter in output port
Strange thing is I can enter let's say 2.8, but as soon as the dialog window is closed and opened again the value has changed to 3.0
Rover Vitesse 3.5
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: pulsewidth as parameter in output port
What firmware and what version of TunerStudio?
2.8 should work fine.
2.8 should work fine.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Re: pulsewidth as parameter in output port
2.6.0.1.
But if I do help/search for update it comes back with the message "no updates available, 2.6.0.1 is the latest version"
I don't understand.
But if I do help/search for update it comes back with the message "no updates available, 2.6.0.1 is the latest version"
I don't understand.
Rover Vitesse 3.5
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: pulsewidth as parameter in output port
2.6.01 is the current stable versionLT401Vette wrote:What firmware and what version of TunerStudio?
perhaps an msq.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Re: pulsewidth as parameter in output port
MSQ attached.
Strange thing is that offline I can change the pw decimal today (couldn't yesterday), but not online.
The hysteresis decimal I cannot change offline today, I could do that yesterday.
Beats me.
Strange thing is that offline I can change the pw decimal today (couldn't yesterday), but not online.
The hysteresis decimal I cannot change offline today, I could do that yesterday.
Beats me.
Rover Vitesse 3.5
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: pulsewidth as parameter in output port
I am seeing some strange behavior here. It was working fine for me at 1st, then they stopped.
I will look into it.
I will look into it.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: pulsewidth as parameter in output port
If I make a large change, say more than a delta of 1.0 it does seem to stick every time.
So the work around seems to be to change it a large amount, close the dialog, then go to your desired value.
Quite odd.
So the work around seems to be to change it a large amount, close the dialog, then go to your desired value.
Quite odd.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Re: pulsewidth as parameter in output port
Doesn't work on the car. It keeps rounding off the decimals. If I enter 1.6, close and open the dialog it's changed to 2.0 again.
Rover Vitesse 3.5
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor
-
- Site Admin
- Posts: 39615
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: pulsewidth as parameter in output port
You didn't do what Phil suggested.
Change it to 6 and close the window.
Open it again and type in 1.6.
James
Change it to 6 and close the window.
Open it again and type in 1.6.
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: pulsewidth as parameter in output port
Ok, that seems indeed to do the trick. Let me try it on the car tomorrow.
Rover Vitesse 3.5
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor
MS3 full-sequential
36-1 triggerwheel
Direct coil control
Innovate LC1 wideband lambda sensor