Headed to the track tonight and would like to log/veal the engine and take a datalog of the tranny controller. Can I do this with two sessions of tunerstudio open with each on there respective project?
Setup, ms3pro tied via canbus to a microsquirt for the transmission
Taking 2 datalogs simultaneously
Moderator: LT401Vette
-
- Super MS/Extra'er
- Posts: 2639
- Joined: Tue Sep 14, 2004 4:17 pm
- Location: Aberdeen, Wa
Taking 2 datalogs simultaneously
Volvo 940, 2jzge, MS3Pro, daily
240Z, 2JZ, MS3Pro boost control
240Z, 2JZ, MS3Pro boost control
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Taking 2 datalogs simultaneously
If you create a combined project (i.e. with the trans as a "CAN device") your datalogs will include both datasets.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 2639
- Joined: Tue Sep 14, 2004 4:17 pm
- Location: Aberdeen, Wa
Re: Taking 2 datalogs simultaneously
Ahhhh. Very nice. I'll look into that today
Volvo 940, 2jzge, MS3Pro, daily
240Z, 2JZ, MS3Pro boost control
240Z, 2JZ, MS3Pro boost control
-
- Super MS/Extra'er
- Posts: 2639
- Joined: Tue Sep 14, 2004 4:17 pm
- Location: Aberdeen, Wa
Re: Taking 2 datalogs simultaneously
Ok. I created another project and under property's, CAN device I added CAN1 and searched out the configuration file, and tried the .ini file and the cfg file, when the project reloads it comes with a firmware mismatch and if I connect anyway I can take a datalog and have the CAN stuff in there for the tranny but no real data. Temp stays at 0
Volvo 940, 2jzge, MS3Pro, daily
240Z, 2JZ, MS3Pro boost control
240Z, 2JZ, MS3Pro boost control
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Taking 2 datalogs simultaneously
Adding the CAN device is covered in the latest trans manual isn't it ?
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 2639
- Joined: Tue Sep 14, 2004 4:17 pm
- Location: Aberdeen, Wa
Re: Taking 2 datalogs simultaneously
Got it. Clear in the manual. I had had the can setting wrong at 0 rather than 7 as it should have been. All logging now
Thankyou
Thankyou
Volvo 940, 2jzge, MS3Pro, daily
240Z, 2JZ, MS3Pro boost control
240Z, 2JZ, MS3Pro boost control