ts3 indicators not working when connected to ecu
Moderator: LT401Vette
-
- Master MS/Extra'er
- Posts: 643
- Joined: Sun Nov 06, 2005 12:31 am
- Location: NORTHERN CALIFORNIA
ts3 indicators not working when connected to ecu
I am upgraded to 2.9.110 as of today, tuning works well, and shuts of when commanded, with data logging and ve analyze all working and gauges reading the indicator panel at the bottom of the gauge screen doesn't show anything, the not synced light is red and all the other indicators are white. but the gauges are reading and the engine is running and the data logging is working.
64 el camino, 383 SBC, 11.7 to1 CR, accufab tb/rhs intake, 44lb injectors, trick flow heads, xr292r solid roller cam, belt drive camshaft, dry sump oil system, 2400 stall, turbo 350, spooled 9 inch, strange axles, 3.89 gears, dual wideband, full sequential fuel/cop, MS3x using 1.4.1 code.
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: ts3 indicators not working when connected to ecu
Interesting, I had 1 other person with somethings similar. They said it was only on 1 dashboard that it would do this, the others worked.
Also on the dash that didn't do it, it would start working if you went into designer mode then back out.
He sent his dash for me to try to reproduce it. Perhaps if you can post yours also.
Also on the dash that didn't do it, it would start working if you went into designer mode then back out.
He sent his dash for me to try to reproduce it. Perhaps if you can post yours also.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Master MS/Extra'er
- Posts: 643
- Joined: Sun Nov 06, 2005 12:31 am
- Location: NORTHERN CALIFORNIA
Re: ts3 indicators not working when connected to ecu
I am going to attach the file called dashboard.dash. I hope that is the file you are wanting, if not let me know which one you need. I have been using the same dash for quite some time, and it has always worked in the past, is there some setting I might have changed by accident that would cause the indicators to turn off. the indicators were working with 2.9.108, but quit with 2.9.110.
Last edited by kaeman on Wed Apr 13, 2016 9:44 pm, edited 1 time in total.
64 el camino, 383 SBC, 11.7 to1 CR, accufab tb/rhs intake, 44lb injectors, trick flow heads, xr292r solid roller cam, belt drive camshaft, dry sump oil system, 2400 stall, turbo 350, spooled 9 inch, strange axles, 3.89 gears, dual wideband, full sequential fuel/cop, MS3x using 1.4.1 code.
Re: ts3 indicators not working when connected to ecu
I'm getting this on dashes produced by TS 2.6.x. Usually loading the default dash solves the problem, albeit I have to redesign it as I want to.
The man behind MS Labs
2005 Audi A3 2.0L TFSI DSG AWD - Extreme MS3
2002 Mazda Miata 1.8 6sp - Enhanced MS3 1.4.0, sequential injection, sequential ignition, big turbo, lots of boost
2005 Audi A3 2.0L TFSI DSG AWD - Extreme MS3
2002 Mazda Miata 1.8 6sp - Enhanced MS3 1.4.0, sequential injection, sequential ignition, big turbo, lots of boost
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: ts3 indicators not working when connected to ecu
I have been able to reproduce this. It seems repaint isn't getting called after the indicator state changes. Re-sizing the TS windows makes them display correctly.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Master MS/Extra'er
- Posts: 643
- Joined: Sun Nov 06, 2005 12:31 am
- Location: NORTHERN CALIFORNIA
Re: ts3 indicators not working when connected to ecu
I upgraded to tuner studio 2.9.112 last night, I will be working on my vehicle in the next couple of days, would upgrading to the latest version of the firmware 1.4 ( I'm using 1.3.4) help with any of the problems I have been experiencing? Or should I stick with the firmware I have until we get the problems in tuner studio 3 cleared up.
64 el camino, 383 SBC, 11.7 to1 CR, accufab tb/rhs intake, 44lb injectors, trick flow heads, xr292r solid roller cam, belt drive camshaft, dry sump oil system, 2400 stall, turbo 350, spooled 9 inch, strange axles, 3.89 gears, dual wideband, full sequential fuel/cop, MS3x using 1.4.1 code.
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: ts3 indicators not working when connected to ecu
Problems?kaeman wrote:I upgraded to tuner studio 2.9.112 last night, I will be working on my vehicle in the next couple of days, would upgrading to the latest version of the firmware 1.4 ( I'm using 1.3.4) help with any of the problems I have been experiencing? Or should I stick with the firmware I have until we get the problems in tuner studio 3 cleared up.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Master MS/Extra'er
- Posts: 643
- Joined: Sun Nov 06, 2005 12:31 am
- Location: NORTHERN CALIFORNIA
Re: ts3 indicators not working when connected to ecu
Just the indicators and such, the auto tuning is turning off when I click stop now. I am planning on doing some tuning this weekend so I will be able to give some better feedback on the features.
64 el camino, 383 SBC, 11.7 to1 CR, accufab tb/rhs intake, 44lb injectors, trick flow heads, xr292r solid roller cam, belt drive camshaft, dry sump oil system, 2400 stall, turbo 350, spooled 9 inch, strange axles, 3.89 gears, dual wideband, full sequential fuel/cop, MS3x using 1.4.1 code.
-
- Master MS/Extra'er
- Posts: 643
- Joined: Sun Nov 06, 2005 12:31 am
- Location: NORTHERN CALIFORNIA
Re: ts3 indicators not working when connected to ecu
I connected to the ecu and fired up the engine, all indicators and gauges working correctly, TS version 2.9.113 without resizing the screen.
64 el camino, 383 SBC, 11.7 to1 CR, accufab tb/rhs intake, 44lb injectors, trick flow heads, xr292r solid roller cam, belt drive camshaft, dry sump oil system, 2400 stall, turbo 350, spooled 9 inch, strange axles, 3.89 gears, dual wideband, full sequential fuel/cop, MS3x using 1.4.1 code.