IOx issues (MS3 pre-1.5 alpha 4 released)

For discussion of Phil Tobin's Tuner Studio software (Only about the tuning software itself, not about how to tune or firmware features)

Moderator: LT401Vette

Post Reply
jsiedlicki
Master MS/Extra'er
Posts: 687
Joined: Sun Jun 23, 2013 3:52 pm

IOx issues (MS3 pre-1.5 alpha 4 released)

Post by jsiedlicki »

Having an issue with the Generic PWM dialog when working with Jean's TinyIOx board. If you try to switch "Table or Curve" into Curve mode, the dialog grays out the table and does not display the curve graph or the editing rows.

It works correctly using the current stable firmware, 1.4.1

Is this a firmware issue or a problem with Jean's current ini?

MS3-Pro
Using latest TinyIOx firmware: 0.2.0
Screenshot.png
MS3-Pro 1st Gen | Honda K24 Supercharged
MS3/MS3X | SB Ford 347 stroker
racingmini_mtl
Super MS/Extra'er
Posts: 9127
Joined: Sun May 02, 2004 6:51 am
Location: Quebec, Canada
Contact:

Re: MS3 pre-1.5 alpha 4 released

Post by racingmini_mtl »

There was a problem with the ini so if you did not download it recently, you need to use this one: http://www.jbperf.com/io_extender/firmw ... inyIOx.ini. And you need to use the latest TunerStudio version.

Jean
jbperf.com Main site . . . . . . . . . . . . . . . . . . . . . . jbperf.com Forum
Image
jsiedlicki
Master MS/Extra'er
Posts: 687
Joined: Sun Jun 23, 2013 3:52 pm

Re: MS3 pre-1.5 alpha 4 released

Post by jsiedlicki »

racingmini_mtl wrote:There was a problem with the ini so if you did not download it recently, you need to use this one: http://www.jbperf.com/io_extender/firmw ... inyIOx.ini. And you need to use the latest TunerStudio version.

Jean
That is the ini file I'm using. Did a diff compare just to be sure.
MS3-Pro 1st Gen | Honda K24 Supercharged
MS3/MS3X | SB Ford 347 stroker
racingmini_mtl
Super MS/Extra'er
Posts: 9127
Joined: Sun May 02, 2004 6:51 am
Location: Quebec, Canada
Contact:

Re: MS3 pre-1.5 alpha 4 released

Post by racingmini_mtl »

Since this has nothing to do with the MS3 pre-1.5 alpha 4, you should create another thread in the TunerStudio section of the forum (since this seems to be a TS related issue). And in there, post a backup of your project.

Jean
jbperf.com Main site . . . . . . . . . . . . . . . . . . . . . . jbperf.com Forum
Image
LT401Vette
Super MS/Extra'er
Posts: 12684
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC
Contact:

Re: IOx issues (MS3 pre-1.5 alpha 4 released)

Post by LT401Vette »

What version of TS are you using?
(Please don't say the latest)

Can you post / send a Project backup?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
jsiedlicki
Master MS/Extra'er
Posts: 687
Joined: Sun Jun 23, 2013 3:52 pm

Re: IOx issues (MS3 pre-1.5 alpha 4 released)

Post by jsiedlicki »

I am using TS v 3.0.05

Here is a backup of the project. It is not from a running car, I am just setting everything up.

The problem does not happen if I load the current stable firmware and try it it (v 1.4.1) so I'm not sure that it is a TS issue.

Since you can only upload a 715kb file I deleted everything I think is not needed in the zip. If I deleted something important, let me know.

Thanks
MS3-Pro 1st Gen | Honda K24 Supercharged
MS3/MS3X | SB Ford 347 stroker
LT401Vette
Super MS/Extra'er
Posts: 12684
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC
Contact:

Re: IOx issues (MS3 pre-1.5 alpha 4 released)

Post by LT401Vette »

It looks like you have it set to use a Curve Editor instead of the Table, so the table should be disabled.
You also have it set to use "RC Servo Extended (0.5-2.5ms, 50Hz)" in Base I/O settings.

However, in the ini there is no valid Curve option for timer_source2 = 3, so I don't think this is a valid setup.

Jean?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
racingmini_mtl
Super MS/Extra'er
Posts: 9127
Joined: Sun May 02, 2004 6:51 am
Location: Quebec, Canada
Contact:

Re: IOx issues (MS3 pre-1.5 alpha 4 released)

Post by racingmini_mtl »

Yep, that was a mistake on my part. I had forgotten to change (and test) that when I added the new option (timer_source2 = 3). I have updated the ini file on my site so if you reload it from the same link as above, you will get the corrected one.

By the way, timer_source2 == 2 was supposed to be timer_source >= 2 since options 2 and 3 need the same table.

Jean
jbperf.com Main site . . . . . . . . . . . . . . . . . . . . . . jbperf.com Forum
Image
jsiedlicki
Master MS/Extra'er
Posts: 687
Joined: Sun Jun 23, 2013 3:52 pm

Re: IOx issues (MS3 pre-1.5 alpha 4 released)

Post by jsiedlicki »

Works after updating with Jean's fix.

Thanks everyone.
MS3-Pro 1st Gen | Honda K24 Supercharged
MS3/MS3X | SB Ford 347 stroker
Post Reply