firmware upgrade issue (ini)

For discussion of Phil Tobin's Tuner Studio software (Only about the tuning software itself, not about how to tune or firmware features)

Moderator: LT401Vette

Post Reply
mase86
MS/Extra Newbie
Posts: 3
Joined: Fri Dec 30, 2016 9:45 am

firmware upgrade issue (ini)

Post by mase86 »

1996 Toyota Corolla ae111 blacktop 20v
MS1 v3

I have a project I have been working on and haven't touched it in over a year. About a week ago when setting it back up again i had to update TS to the new version. Apon startup I received the firmware signature mismatch. Went to update firmware but it still gives me a window that says TS doesn't have the ecu definition ini that's compatible with the firmware. Can I just go to the index of ini page and grab the mS1 ini file from there? Thx.
ImageImageImage


Sent from my iPhone using Tapatalk
jsmcortina
Site Admin
Posts: 39585
Joined: Mon May 03, 2004 1:34 am
Location: Birmingham, UK
Contact:

Re: firmware upgrade issue (ini)

Post by jsmcortina »

Seems like TunerStudio is perhaps being a bit strange here and I'm not sure it really makes sense. Best to wait for the developers' input.

James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk

My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
mase86
MS/Extra Newbie
Posts: 3
Joined: Fri Dec 30, 2016 9:45 am

firmware upgrade issue (ini)

Post by mase86 »

I went in today and opened the project properties box. Firmware is 029y4 but with I go to find the Ecu definition it gives me 029y3. I have the new firmware (029y4) and when I open the msns config setting it says the signature is 029y3. The signature seems to be correct when looking at it.

ImageImage


Sent from my iPhone using Tapatalk
jsmcortina
Site Admin
Posts: 39585
Joined: Mon May 03, 2004 1:34 am
Location: Birmingham, UK
Contact:

Re: firmware upgrade issue (ini)

Post by jsmcortina »

That's correct. The issue is what you posted in your first post.

James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk

My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
LT401Vette
Super MS/Extra'er
Posts: 12697
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC
Contact:

Re: firmware upgrade issue (ini)

Post by LT401Vette »

It appears you are getting timeouts from the controller.
Your signature is truncated and the versionInfo 'T' command appears to be timing out.

What type of connection are you using?

If you open Mini-Term and type a T, what do you get back?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
mase86
MS/Extra Newbie
Posts: 3
Joined: Fri Dec 30, 2016 9:45 am

firmware upgrade issue (ini)

Post by mase86 »

I did a port check as well as the Mini-term. Here is what I received from both. I'm using a USB to serial cable (PL- 2303 driver ver. 2.0.2.8) ImageImage
Image
https://vimeo.com/197975121



Sent from my iPhone using Tapatalk
Post Reply