1996 Toyota Corolla ae111 blacktop 20v
MS1 v3
I have a project I have been working on and haven't touched it in over a year. About a week ago when setting it back up again i had to update TS to the new version. Apon startup I received the firmware signature mismatch. Went to update firmware but it still gives me a window that says TS doesn't have the ecu definition ini that's compatible with the firmware. Can I just go to the index of ini page and grab the mS1 ini file from there? Thx.
Sent from my iPhone using Tapatalk
firmware upgrade issue (ini)
Moderator: LT401Vette
-
- Site Admin
- Posts: 39618
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: firmware upgrade issue (ini)
Seems like TunerStudio is perhaps being a bit strange here and I'm not sure it really makes sense. Best to wait for the developers' input.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
firmware upgrade issue (ini)
I went in today and opened the project properties box. Firmware is 029y4 but with I go to find the Ecu definition it gives me 029y3. I have the new firmware (029y4) and when I open the msns config setting it says the signature is 029y3. The signature seems to be correct when looking at it.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
-
- Site Admin
- Posts: 39618
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: firmware upgrade issue (ini)
That's correct. The issue is what you posted in your first post.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: firmware upgrade issue (ini)
It appears you are getting timeouts from the controller.
Your signature is truncated and the versionInfo 'T' command appears to be timing out.
What type of connection are you using?
If you open Mini-Term and type a T, what do you get back?
Your signature is truncated and the versionInfo 'T' command appears to be timing out.
What type of connection are you using?
If you open Mini-Term and type a T, what do you get back?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
firmware upgrade issue (ini)
I did a port check as well as the Mini-term. Here is what I received from both. I'm using a USB to serial cable (PL- 2303 driver ver. 2.0.2.
https://vimeo.com/197975121
Sent from my iPhone using Tapatalk
https://vimeo.com/197975121
Sent from my iPhone using Tapatalk