Page 1 of 1

Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Fri May 19, 2017 11:43 am
by 5.0Thunder
As we utilize the VEAL tool during tuning, the map generated can typically be peaky. After every tuning session I go inside and smooth things out manually based on what the engine is wanting in certain areas and if those areas were swept a lot during the session. Would it be wise to incorporate auto-smoothing into the VEAL feature that factors in hit-counts, interpolations between cells, etc.?

I'm about to have some load bearing dyno time where I want to experiment with using VEAL while targeting single cells and the auto-smoothing feature would be handy here. I think i'd basically be able to just let the engine run in each cell and not really touch anything but the "save" buttons.

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Sat May 20, 2017 10:51 am
by rukavina
I also have a suggestion.... with Ms you can toggle outputs on and off to test. I don't know of that function on this board. I was able to test the controller I just built by faking a vss signal and running it thru it's paces but it would have been nice to just turn things on and off while on the bench...

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Thu May 25, 2017 9:39 am
by 5.0Thunder
^^ May be better to post a new thread since that's a different feature.

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Sat Jun 10, 2017 12:12 pm
by 5.0Thunder
Bump!

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Tue Jun 20, 2017 5:51 am
by 5.0Thunder
:?: :?: :?:

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Mon Jun 26, 2017 11:49 am
by 5.0Thunder
bump

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Thu Jun 29, 2017 6:50 am
by sschutte
Feature request received. Please give us a week to review and get back to you.

Schutte

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Sun May 27, 2018 7:11 am
by martroy
What have you decided?

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Mon Oct 14, 2019 6:14 am
by 5.0Thunder
Never heard back on this one.

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Tue Oct 15, 2019 11:54 am
by mapdaddy
I've often wondered about this feature. Would be nice to enable and disable the smoothing if it was implemented.

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Wed Oct 16, 2019 6:08 am
by vw_chuck
There is already a smoothing function. Just go to the map, highlight and hit the button.

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Wed Oct 16, 2019 6:58 am
by 5.0Thunder
Woah, this will throw stuff out of whack. Areas that are perfect and already smooth will be elevated or decreased, throwing AFR's off. Idle area would be increased, lots of things you don't want to touch will be modified.

Using the hit count during VEAL and targeting only the cells around your corrected area should keep all that from happening. I'm sure there is a more elegant and useful way of doing it that these guys are working on.

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Wed Oct 16, 2019 7:56 am
by Dennis_Zx7r
Yeah, the smoothing should be limited to cells that have a very low hit count. However, this would require recording how often the cells have been hit in previous tuning sessions or you could only use it once.

Re: Feature Discussion/Suggestion: VEAL Auto-Smooth

Posted: Tue Jan 14, 2020 10:36 am
by 5.0Thunder
Bump for update