Generated VE Table

For discussion of Phil Tobin's Tuner Studio software (Only about the tuning software itself, not about how to tune or firmware features)

Moderator: LT401Vette

Post Reply
kjones6039
Super MS/Extra'er
Posts: 1986
Joined: Sat Jul 22, 2006 8:02 pm
Location: Eureka, NV USA
Contact:

Generated VE Table

Post by kjones6039 »

I generated the attached VE table using TS. As you can see TS returned a table with the last 3 columns set to 6000 rpm! Any thoughts on this?

Ken

EDIT: Also note that I was the one who set the idle bins to 46. TS did not return those numbers.
Generated Ign Table.png
Last edited by kjones6039 on Mon Jun 19, 2017 11:55 am, edited 1 time in total.
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
benckj
Master MS/Extra'er
Posts: 464
Joined: Mon Dec 19, 2011 3:21 pm

Re: Generated VE Table

Post by benckj »

Can't see the problem, just add some intermediate columns, check your target AFR table and generate again. I probably used those tools a dozen times before I started road running.

Jim
Toyota MR2 98 3sgte
MSPNP2 with 3.57 mainboard
Innovate WB O2 & soon to be external GM 3 bar MAP
FTDI USB interface on SD Android 5.1 head unit
TD05SL2-18g with external WG
HKS EBC running 17psi boost.
A2W IC with WI 50/50 meth/water
LT401Vette
Super MS/Extra'er
Posts: 12697
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC
Contact:

Re: Generated VE Table

Post by LT401Vette »

What did you use for inputs?

What is the maximum RPM under general settings?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
kjones6039
Super MS/Extra'er
Posts: 1986
Joined: Sat Jul 22, 2006 8:02 pm
Location: Eureka, NV USA
Contact:

Re: Generated VE Table

Post by kjones6039 »

LT401Vette wrote:What did you use for inputs?
The wrong numbers of course!!! :oops: So.... is that a problem??? :shock:

I dumb thumbed the inputs and set both redline and max HP to the same number (6000 rpm)! Needless to say, TS didn't like that! :lol:

Corrected the numbers and voila!

Apologies for the false start!!!

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
Post Reply