I have wired in a 0-5 volt reference wire to my I/O box using CANADC06. Id like to run a guage displaying the current selected rpm if we can. I run a windows tablet in my drag car and use TS as my dashboard
Attached is my current tune to make sure its wired right. I am not using generic sensor input, just having the 0-5 volt come in on canadc06 selected under variable launch
displaying current launch rpm
Moderator: LT401Vette
-
- Super MS/Extra'er
- Posts: 2639
- Joined: Tue Sep 14, 2004 4:17 pm
- Location: Aberdeen, Wa
displaying current launch rpm
Volvo 940, 2jzge, MS3Pro, daily
240Z, 2JZ, MS3Pro boost control
240Z, 2JZ, MS3Pro boost control
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: displaying current launch rpm
There's no built-in method.
However, how about allowing input sharing and configuring that as a generic sensor, linear with the 0 and 5V values as your min and max launch numbers. (I haven't tested this.)
James
However, how about allowing input sharing and configuring that as a generic sensor, linear with the 0 and 5V values as your min and max launch numbers. (I haven't tested this.)
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 2639
- Joined: Tue Sep 14, 2004 4:17 pm
- Location: Aberdeen, Wa
Re: displaying current launch rpm
Tried this out over the weekend, the variable launch works, but when I also turn on the input into he generic table to create a gauge, i get the dreaded input pin conflict error
I'll use some tape around the knob and write in what the current positions will be
I'll use some tape around the knob and write in what the current positions will be
Volvo 940, 2jzge, MS3Pro, daily
240Z, 2JZ, MS3Pro boost control
240Z, 2JZ, MS3Pro boost control
-
- Super MS/Extra'er
- Posts: 12732
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: displaying current launch rpm
Did you turn on input sharing?nathaninwa wrote:Tried this out over the weekend, the variable launch works, but when I also turn on the input into he generic table to create a gauge, i get the dreaded input pin conflict error
I'll use some tape around the knob and write in what the current positions will be
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Super MS/Extra'er
- Posts: 2639
- Joined: Tue Sep 14, 2004 4:17 pm
- Location: Aberdeen, Wa
Re: displaying current launch rpm
I guess I'm unfamiliar with this feature. Where do I find it?
Volvo 940, 2jzge, MS3Pro, daily
240Z, 2JZ, MS3Pro boost control
240Z, 2JZ, MS3Pro boost control
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: displaying current launch rpm
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 2639
- Joined: Tue Sep 14, 2004 4:17 pm
- Location: Aberdeen, Wa
Re: displaying current launch rpm
Sharing input did the trick.
Volvo 940, 2jzge, MS3Pro, daily
240Z, 2JZ, MS3Pro boost control
240Z, 2JZ, MS3Pro boost control