Unexpected error occoured opening project
Moderator: LT401Vette
-
- MS/Extra Newbie
- Posts: 23
- Joined: Fri Jan 13, 2017 6:26 am
Unexpected error occoured opening project
I was about to open my current tune file and got this error.
"Unexpected error occoured opening project"
I tried looking for the back-ups but that aint woring since the tune file cant open.
If I open an other tune file it can'n load the back-up of my other file.
How can I get my tune back up and running?
Can it download from the MS2? Cant seem to see how that works.
"Unexpected error occoured opening project"
I tried looking for the back-ups but that aint woring since the tune file cant open.
If I open an other tune file it can'n load the back-up of my other file.
How can I get my tune back up and running?
Can it download from the MS2? Cant seem to see how that works.
E28 525e -M20B27- DIS, MS2 V3.0
-
- Super MS/Extra'er
- Posts: 1986
- Joined: Sat Jul 22, 2006 8:02 pm
- Location: Eureka, NV USA
- Contact:
Re: Unexpected error occoured opening project
You should just be able to create a new project and then load your tune from your MS box.Dutchredhead wrote:Can it download from the MS2? Cant seem to see how that works.
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
-
- MS/Extra Newbie
- Posts: 23
- Joined: Fri Jan 13, 2017 6:26 am
Re: Unexpected error occoured opening project
Thx. I'll try that tomorrow.
E28 525e -M20B27- DIS, MS2 V3.0
-
- Experienced MS/Extra'er
- Posts: 372
- Joined: Sat Dec 31, 2011 6:10 am
- Location: Netherlands
- Contact:
Re: Unexpected error occoured opening project
I've encountered those errors a couple of times, but was able to go ahead after that without issues.
Daily driver: 1973 Dodge Dart - 360ci engine - 11.3:1cr - MS3x - ignition only. 42RH/A500 OD+LU transmission / 3.23 gears
--------------
Website: https://www.bigblockmopar.nl/
YouTube Channel: https://www.youtube.com/c/BigBlockMopar
--------------
Website: https://www.bigblockmopar.nl/
YouTube Channel: https://www.youtube.com/c/BigBlockMopar
-
- Super MS/Extra'er
- Posts: 1986
- Joined: Sat Jul 22, 2006 8:02 pm
- Location: Eureka, NV USA
- Contact:
Re: Unexpected error occoured opening project
I have seen that message also and used the procedure I described above. Worked OK for me.BigBlockMopar wrote:I've encountered those errors a couple of times, but was able to go ahead after that without issues.
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Unexpected error occoured opening project
I'd like to know why it occurred. There ought to be a better remedy than "start again" and TunerStudio should be able to fix itself.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- MS/Extra Newbie
- Posts: 23
- Joined: Fri Jan 13, 2017 6:26 am
Re: Unexpected error occoured opening project
Couldnt agree more. It just wont go into that file again. Despite the individual file's are to be accesed.jsmcortina wrote:I'd like to know why it occurred. There ought to be a better remedy than "start again" and TunerStudio should be able to fix itself.
James
Loaded the dash and .table files as well into a other project when I was trying to get it pieced back together.
I just opened a new project, loaded data from ECU, so i'm back up and running.
Thx Ken, it worked.
E28 525e -M20B27- DIS, MS2 V3.0
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Unexpected error occoured opening project
When this has been reported in the past, what I have found is the project.properties file was empty.
That makes the project invalid and it can't load. I have never been able to find anyone that can reproduce this, a few times it was shortly before their hard drive took a dump, other times that wasn't the case.
In TS 3.0.x, TS saves a backup of the project.properties so if it is corrupt or empty, it can fall back to that. It looks like in your case that didn't happen either. I would be interested in seeing your project to see if the backup is also empty?
That makes the project invalid and it can't load. I have never been able to find anyone that can reproduce this, a few times it was shortly before their hard drive took a dump, other times that wasn't the case.
In TS 3.0.x, TS saves a backup of the project.properties so if it is corrupt or empty, it can fall back to that. It looks like in your case that didn't happen either. I would be interested in seeing your project to see if the backup is also empty?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Experienced MS/Extra'er
- Posts: 372
- Joined: Sat Dec 31, 2011 6:10 am
- Location: Netherlands
- Contact:
Re: Unexpected error occoured opening project
Maybe a lousy USB connection could corrupt the transfer?
Come to think of it, I haven't seen these errors anymore lately, but I'm also using a different USB cable now that clips/hooks better into the tablet I'm using.
Before I was using a Chinese adapter from regular USB to mini-USB.
Come to think of it, I haven't seen these errors anymore lately, but I'm also using a different USB cable now that clips/hooks better into the tablet I'm using.
Before I was using a Chinese adapter from regular USB to mini-USB.
Daily driver: 1973 Dodge Dart - 360ci engine - 11.3:1cr - MS3x - ignition only. 42RH/A500 OD+LU transmission / 3.23 gears
--------------
Website: https://www.bigblockmopar.nl/
YouTube Channel: https://www.youtube.com/c/BigBlockMopar
--------------
Website: https://www.bigblockmopar.nl/
YouTube Channel: https://www.youtube.com/c/BigBlockMopar
-
- MS/Extra Newbie
- Posts: 23
- Joined: Fri Jan 13, 2017 6:26 am
Re: Unexpected error occoured opening project
I was opening it off line. Wasn't connected to USB.
I can send the old files to you, Phil.
I can send the old files to you, Phil.
E28 525e -M20B27- DIS, MS2 V3.0