Rolling back to previous versions
Moderator: LT401Vette
-
- MS/Extra Newbie
- Posts: 10
- Joined: Sat Sep 02, 2017 12:07 am
Rolling back to previous versions
I am wondering if it is possible to roll back to a previous version of Tunerstudio
5 days ago I uploaded a new tune into my megasquirt with no issues..
The next day I connected my laptop and opened TS it automatically installed a new update from version 3.0.2 to 3.0.28
Now I am unable to get TS to communicate with my ecu... Port check shows the connection... I thought maybe I should update the firmware , so I did.. no issues with that.. but I still cannot get it to communicate with TS. Is there anyway I can roll back to the last version of TS which worked..
5 days ago I uploaded a new tune into my megasquirt with no issues..
The next day I connected my laptop and opened TS it automatically installed a new update from version 3.0.2 to 3.0.28
Now I am unable to get TS to communicate with my ecu... Port check shows the connection... I thought maybe I should update the firmware , so I did.. no issues with that.. but I still cannot get it to communicate with TS. Is there anyway I can roll back to the last version of TS which worked..
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Rolling back to previous versions
Are you getting any error?
Are you sure you updated from 3.0.2? (That is quite old and never a public release, the more recent stable version is 3.0.22)
Can you create a TunerStudio Debug Package from under the Help menu?
Are you sure you updated from 3.0.2? (That is quite old and never a public release, the more recent stable version is 3.0.22)
Can you create a TunerStudio Debug Package from under the Help menu?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- MS/Extra Newbie
- Posts: 10
- Joined: Sat Sep 02, 2017 12:07 am
Re: Rolling back to previous versions
My Error is
"error reading data from My Car after 9 attempts
error message returned
could not process comminstruction
error written to log
timeout after 401ms . requested timeout :400, expected bytes:260, bytes read :89
I have enclosed my debug file as requested
"error reading data from My Car after 9 attempts
error message returned
could not process comminstruction
error written to log
timeout after 401ms . requested timeout :400, expected bytes:260, bytes read :89
I have enclosed my debug file as requested
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Rolling back to previous versions
Where?Intimidation 86 wrote: I have enclosed my debug file as requested
Ok, so it sounds like you are connecting fine, but it can not successfully read the tune data.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- MS/Extra Newbie
- Posts: 10
- Joined: Sat Sep 02, 2017 12:07 am
Re: Rolling back to previous versions
I uploaded the zip file using the upload attachment button below
I'll try again tonight
I'll try again tonight
-
- MS/Extra Newbie
- Posts: 10
- Joined: Sat Sep 02, 2017 12:07 am
Re: Rolling back to previous versions
here is the debug I was asked for
thanks
thanks
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Rolling back to previous versions
That debug package does not have your project in it. Was the Project not open?
No project means I can't see how things are setup.
Also it would be good if Comm Debug was turned on for a connection try..
However, what I can see in the log is that it is indeed finding the controller just fine, but gets a timeout on every attempt to read tune data.
The main thing that can cause this is if in Project Properties CAN_COMMANDS is turned off and you are set to the wrong CAN ID for the main controller.
Your MegaSquirt is still running on CAN ID 0, so check this:
- In TunerStudio with your project open, press CTRL+P
The Project Properties dialog should open.
- Click the "CAN Devices" tab
- Check the setting "Main Controller CAN ID"
That should be set to 0, if not, set that to 0 and click OK
If that isn't it, turn on Comm Debug and try to connect again. Make a new Debug Package and post / send.
No project means I can't see how things are setup.
Also it would be good if Comm Debug was turned on for a connection try..
However, what I can see in the log is that it is indeed finding the controller just fine, but gets a timeout on every attempt to read tune data.
The main thing that can cause this is if in Project Properties CAN_COMMANDS is turned off and you are set to the wrong CAN ID for the main controller.
Your MegaSquirt is still running on CAN ID 0, so check this:
- In TunerStudio with your project open, press CTRL+P
The Project Properties dialog should open.
- Click the "CAN Devices" tab
- Check the setting "Main Controller CAN ID"
That should be set to 0, if not, set that to 0 and click OK
If that isn't it, turn on Comm Debug and try to connect again. Make a new Debug Package and post / send.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- MS/Extra Newbie
- Posts: 10
- Joined: Sat Sep 02, 2017 12:07 am
Re: Rolling back to previous versions
Thanks I'll try that when I get home
-
- MS/Extra Newbie
- Posts: 10
- Joined: Sat Sep 02, 2017 12:07 am
Re: Rolling back to previous versions
Ok. I reset the CAN I'd to 0 and it's working like a charm.. thanks very much for the help
-
- MS/Extra Newbie
- Posts: 10
- Joined: Sat Sep 02, 2017 12:07 am
Re: Rolling back to previous versions
Ok so I now have another issue
Since updating the firmware I am unable to get the engine to start..
ignition is firing I get plenty of spark but my injectors are not working
I tried using the port output test and am not getting any response from them ( I should be able to hear them buzz )
same results with both bank 1 and 2
any thoughts ???
MegaSquirt-II V3.57 plug and play for 1986-1993 5.0 Mustang
If I plug in the factory ECU the car will start....
Since updating the firmware I am unable to get the engine to start..
ignition is firing I get plenty of spark but my injectors are not working
I tried using the port output test and am not getting any response from them ( I should be able to hear them buzz )
same results with both bank 1 and 2
any thoughts ???
MegaSquirt-II V3.57 plug and play for 1986-1993 5.0 Mustang
If I plug in the factory ECU the car will start....
-
- Site Admin
- Posts: 39618
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Rolling back to previous versions
Not sure how this is a TunerStudio issue ?
If you have a setup issue, best to post with tune and log into one of the ECU specific support sections.
James
If you have a setup issue, best to post with tune and log into one of the ECU specific support sections.
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- MS/Extra Newbie
- Posts: 10
- Joined: Sat Sep 02, 2017 12:07 am
Re: Rolling back to previous versions
I was just wondering because before the firmware update the car would start and run.....