Feature...

For discussion of Phil Tobin's Tuner Studio software (Only about the tuning software itself, not about how to tune or firmware features)

Moderator: LT401Vette

Post Reply
NiceMan
Experienced MS/Extra'er
Posts: 206
Joined: Fri Mar 25, 2011 11:51 am
Location: Finland
Contact:

Feature...

Post by NiceMan »

First sorry my English...

I have mind what missing from TS... Automatic system make AFR table... And them my mind to this...

I make VE table to perfect manual.. its good if TS can calculate new AFR table from VE table so later can use automatic correct
Another way is hard, drive and make AFR table whit manual.
If not catch my mind, ask free.

Another feature is calculate new VE and spark table... Mind: you make 16x16 ready but want change it to 16x32 and now its need make manual, why not just push button and its make to you new 16x32 or 32x16 table from old 16x16 ...
https://www.facebook.com/PikkiS-112502032715453/
https://www.theniceman.com/coppermine/
Ford Taunus Coupe 1975 2.0i Turbo
Ms3 + MS3x in Taunus
MS3 Pro Ultimate in PikkiS
DaveEFI
Super MS/Extra'er
Posts: 4175
Joined: Sun Apr 15, 2012 12:55 am
Location: SW London, UK

Re: Feature...

Post by DaveEFI »

Think to generate a half decent AFR table, you'd need to know the engine design. Outside the scope of most simple software.
Rover SD1 3.5 EFI
MS2 V3
EDIS
Tech Edge O2
London UK.
NiceMan
Experienced MS/Extra'er
Posts: 206
Joined: Fri Mar 25, 2011 11:51 am
Location: Finland
Contact:

Re: Feature...

Post by NiceMan »

DaveEFI wrote:Think to generate a half decent AFR table, you'd need to know the engine design. Outside the scope of most simple software.
Or use OS2 sensor read and save to afr table...
And make when VE table is perfect and want make afr table show some.
https://www.facebook.com/PikkiS-112502032715453/
https://www.theniceman.com/coppermine/
Ford Taunus Coupe 1975 2.0i Turbo
Ms3 + MS3x in Taunus
MS3 Pro Ultimate in PikkiS
DaveEFI
Super MS/Extra'er
Posts: 4175
Joined: Sun Apr 15, 2012 12:55 am
Location: SW London, UK

Re: Feature...

Post by DaveEFI »

The O2 sensor generally refers to the AFR table. But no reason not to note the AFR where it runs best at a specific load and base your AFR table on that. But you might then have to alter the VE table.
Rover SD1 3.5 EFI
MS2 V3
EDIS
Tech Edge O2
London UK.
NiceMan
Experienced MS/Extra'er
Posts: 206
Joined: Fri Mar 25, 2011 11:51 am
Location: Finland
Contact:

Re: Feature...

Post by NiceMan »

So any mind at make afr table from os2 sensor read ?
https://www.facebook.com/PikkiS-112502032715453/
https://www.theniceman.com/coppermine/
Ford Taunus Coupe 1975 2.0i Turbo
Ms3 + MS3x in Taunus
MS3 Pro Ultimate in PikkiS
LT401Vette
Super MS/Extra'er
Posts: 12697
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC
Contact:

Re: Feature...

Post by LT401Vette »

NiceMan wrote:So any mind at make afr table from os2 sensor read ?
MegaLogViewer HD can do that using the Histogram / Table generator.

https://www.youtube.com/watch?v=CG_kY3K ... ture=share
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Post Reply