Closed Loop Idle Initial Values

For discussion of Phil Tobin's Tuner Studio software (Only about the tuning software itself, not about how to tune or firmware features)

Moderator: LT401Vette

Closed Loop Idle Initial Values

Postby belalegosi » Wed Oct 11, 2017 8:36 pm

What are the units of the column (PWMIDLE..)?
I'm assuming it is Load (kpa) but when connected and idling the tracking icon is up in the 110/140 range.

MS3 using a stepper motor for IAC.
Screen Shot 2017-10-11 at 9.48.38 PM.png
Screen Shot 2017-10-11 at 9.48.38 PM.png (51.36 KiB) Viewed 161 times


Thanks.
belalegosi
MS/Extra Newbie
 
Posts: 32
Joined: Thu Oct 27, 2011 5:43 pm

Re: Closed Loop Idle Initial Values

Postby jsmcortina » Thu Oct 12, 2017 1:22 am

Temperature, usually air temp.

James
I can supply, repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk

My Success story: viewtopic.php?f=104&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
jsmcortina
Site Admin
 
Posts: 33907
Joined: Mon May 03, 2004 1:34 am
Location: Birmingham, UK

Re: Closed Loop Idle Initial Values

Postby belalegosi » Thu Oct 12, 2017 9:32 am

Thanks James.
I was WAY off! This explains why my idle is terrible when cold but pretty mint when warm :lol:
belalegosi
MS/Extra Newbie
 
Posts: 32
Joined: Thu Oct 27, 2011 5:43 pm

Re: Closed Loop Idle Initial Values

Postby belalegosi » Thu Oct 12, 2017 9:41 am

One more question that I'm not sure if I should start a new thread.

How do I datalog indicators?
example: CL idle, Fuel Cut, Launch In, etc
belalegosi
MS/Extra Newbie
 
Posts: 32
Joined: Thu Oct 27, 2011 5:43 pm

Re: Closed Loop Idle Initial Values

Postby LT401Vette » Thu Oct 12, 2017 10:23 am

Most are logged, indirectly if they are not directly.

They are sometimes hiding in the Status Bit fields.

Check in the manual and you can see what status field and bit represents what you are seeking.
Then in MLV you can add a calculated field to show it.

This is also something I was thinking of adding to TS.
Somewhere adding a list of all indicators defined in the ini and make it so you can add them to the custom.ini to be data logged.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
User avatar
LT401Vette
Super MS/Extra'er
 
Posts: 10389
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC

Re: Closed Loop Idle Initial Values

Postby belalegosi » Thu Oct 12, 2017 11:04 am

Thanks Phil!
Simplifying it in a future release would definitely be helpful.
belalegosi
MS/Extra Newbie
 
Posts: 32
Joined: Thu Oct 27, 2011 5:43 pm


Return to Tuner Studio

Who is online

Users browsing this forum: Yahoo [Bot] and 2 guests