Knock module for MS3 (beta test)
Moderators: jsmcortina, muythaibxr
Re: Knock module for MS3 (beta test)
James, any estimate at all of when the next batch will be out? Or if I can get one now? Buttoning up my buddy's car after swapping in a new motor, i think the old one cracked a piston from a bad spot of gas, we were running the ms3x but with no knock sensor. We really need it now!
-
- Helpful MS/Extra'er
- Posts: 142
- Joined: Sun Nov 07, 2004 10:15 pm
- Location: Southern Arizona
Re: Knock module for MS3 (beta test)
Are you going to be bringing any (for distribution) to the MegaMeet this weekend? I'd like to get one but I do not have a car to run it on right now so you can put me on the bottom of the list.
Richard
Richard
-
- Site Admin
- Posts: 8230
- Joined: Thu Oct 14, 2004 12:48 pm
Re: Knock module for MS3 (beta test)
James and I are not attending the megameet this year.
Ken
Ken
Megasquirt is not for use on pollution controlled vehicles. Any advice I give is for off road use only.
-
- Helpful MS/Extra'er
- Posts: 142
- Joined: Sun Nov 07, 2004 10:15 pm
- Location: Southern Arizona
Re: Knock module for MS3 (beta test)
Bummer... was a hoot last time
Either way... go ahead and put my at the bottom of the list.
Richard
Either way... go ahead and put my at the bottom of the list.
Richard
Re: Knock module for MS3 (beta test)
Does the MS3 allow for the ability to set per-cyl ignition trim through CAN?
Toyota Celica GT4/Alltrac with 5S-GTE stroker (2.2L I4 turbo, high CR) on E85 w/FlexFuel.
MS3 + MS3X + KnockBoard + RTC + BT + DIY CAN-IO-Board + DIY CAN Digital Dash.
MS3 + MS3X + KnockBoard + RTC + BT + DIY CAN-IO-Board + DIY CAN Digital Dash.
Re: Knock module for MS3 (beta test)
I really need this board. The car is running now and we're waiting on the knock board to run more boat. Anyone have a board to sell?
Re: Knock module for MS3 (beta test)
Im after one also!
Toyota Celica GT4/Alltrac with 5S-GTE stroker (2.2L I4 turbo, high CR) on E85 w/FlexFuel.
MS3 + MS3X + KnockBoard + RTC + BT + DIY CAN-IO-Board + DIY CAN Digital Dash.
MS3 + MS3X + KnockBoard + RTC + BT + DIY CAN-IO-Board + DIY CAN Digital Dash.
Re: Knock module for MS3 (beta test)
Nice. I notice that a 2012 Chrysler ECU uses this same chip.
Does anyone have some audio recordings from knock sensors to test and tune this with?
Does anyone have some audio recordings from knock sensors to test and tune this with?
Non link censored by admin.
-
- Master MS/Extra'er
- Posts: 756
- Joined: Thu Oct 20, 2005 11:09 am
- Location: Ogden UT USA
- Contact:
Re: Knock module for MS3 (beta test)
Is there any news on this? I keep watching this thread an it doesn't look like there is any movement on it. Where is this at and when is the next round of boards?
Brent Savage
life behind the zion curtain
90 audi RS2 20VTQ 6sp MS3, MSX COP and Sequential and now MAF
87 Scirocco 2.0 ABA 16v EIP tubular cast MSII COP
86 Audi 4K20VTQ MSII
90 Audi 90 sedan 3.6l DOHC V8TT (project car)
89 VW cabbie (bitch basket) 2.0 ABA Turbo MSII
life behind the zion curtain
90 audi RS2 20VTQ 6sp MS3, MSX COP and Sequential and now MAF
87 Scirocco 2.0 ABA 16v EIP tubular cast MSII COP
86 Audi 4K20VTQ MSII
90 Audi 90 sedan 3.6l DOHC V8TT (project car)
89 VW cabbie (bitch basket) 2.0 ABA Turbo MSII
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Knock module for MS3 (beta test)
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: Knock module for MS3 (beta test)
Just got off the phone with the contract manufacturer. A couple of the items on the initial list we'd sent them had a long lead time and I was able to come up with a few substitutions. We'll have an update fairly soon on an ETA.
Matt Cramer -1966 Dodge Dart slant six running on MS3X
Re: Knock module for MS3 (beta test)
Would you give us a brief description of how it works, ease of use, any tuning experiences with it, etc. Just something to wet our appetites. I'm ready to purchase one when they are ready.Matt Cramer wrote:Just got off the phone with the contract manufacturer. A couple of the items on the initial list we'd sent them had a long lead time and I was able to come up with a few substitutions. We'll have an update fairly soon on an ETA.
Re: Knock module for MS3 (beta test)
any news, when they will be available (also the RTC)?
--------------------------------
fun is not a straight line
Sven
http://www.mx-5club-sachsen.de
http://miata.cardomain.com/id/svenmx5
NB-1998-1,6-Garrett T25 HGP Turbo Stage I
fun is not a straight line
Sven
http://www.mx-5club-sachsen.de
http://miata.cardomain.com/id/svenmx5
NB-1998-1,6-Garrett T25 HGP Turbo Stage I
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: Knock module for MS3 (beta test)
Should be ready by August for both of them last I checked.
Matt Cramer -1966 Dodge Dart slant six running on MS3X
Re: Knock module for MS3 (beta test)
What kind of knock sensor are these designed for? I have a bunch of brand new flat response sensors and have been working on my own band pass filter that is no where near as sweet at yours.
Re: Knock module for MS3 (beta test)
any update on this?
81 Porsche 928. 5L 16v, MS3X CNP- full sequential
-
- Master MS/Extra'er
- Posts: 404
- Joined: Tue Dec 30, 2008 9:46 am
- Location: Belgium
- Contact:
Re: Knock module for MS3 (beta test)
don't think it's august yet
2016 Westfield SEiW MX5 1.8 - 6sp - Torsen - MSM turbo - MS3 Pro - 2.3kg/hp
Re: Knock module for MS3 (beta test)
it is in my head!! i hope i can get an assembled 3X with this built in...
81 Porsche 928. 5L 16v, MS3X CNP- full sequential
Re: Knock module for MS3 (beta test)
I love these latest threads about the RTCC and the Knock board related to MS3 development!
I can't wait to finally get back home from this "short term" gig in S. Korea so I can actually fire up my MS3 at home in Seattle with some of these latest features installed.
Thank you MegaSquirt team! Especially James and Ken, for spending countless hours of time to develop code to allow these features to function, among all the other behind the scene things you guys do for the MegaSquirt (and MS Extra/MS3EFI) community!!
I can't wait to finally get back home from this "short term" gig in S. Korea so I can actually fire up my MS3 at home in Seattle with some of these latest features installed.
Thank you MegaSquirt team! Especially James and Ken, for spending countless hours of time to develop code to allow these features to function, among all the other behind the scene things you guys do for the MegaSquirt (and MS Extra/MS3EFI) community!!
Re: Knock module for MS3 (beta test)
what sensor will be recommended for this? (part number etc? )
81 Porsche 928. 5L 16v, MS3X CNP- full sequential