Toyota 3SGE Beams VVTi code
Moderators: jsmcortina, muythaibxr
-
- Super MS/Extra'er
- Posts: 855
- Joined: Sun Oct 10, 2010 6:33 am
Re: Toyota 3SGE Beams VVTi code
This is my "standard" configuration for max9926
R25 IS ONLY FOR HALL SENSOR. NOT INSTALL IN VR SENSOR
I work well with this value and configuration.
R25 IS ONLY FOR HALL SENSOR. NOT INSTALL IN VR SENSOR
I work well with this value and configuration.
Re: Toyota 3SGE Beams VVTi code
I didn't put the R27 and R28 resistors. Should I put them? I'm just working with 4.7kOhm shunt and with 470pF.
I'll try to put a 330pF capacitor on Monday
I'll try to put a 330pF capacitor on Monday
-
- Super MS/Extra'er
- Posts: 855
- Joined: Sun Oct 10, 2010 6:33 am
Re: Toyota 3SGE Beams VVTi code
I do not know the ms3module ....
I think r27 r28 and capacitor is already installed in your card, but please contact Matt for clarification
Test only 4,7k shunt resistor in cranck sensor and 1k shunt sensor in cam sensor without insert capacitor.
I think r27 r28 and capacitor is already installed in your card, but please contact Matt for clarification
Test only 4,7k shunt resistor in cranck sensor and 1k shunt sensor in cam sensor without insert capacitor.
Re: Toyota 3SGE Beams VVTi code
Clean signal with 1k shunt resistor on CMP and 4.7k shunt resistor on CKP.
Wideband helped me a lot to have a good idle (running semi-sequential and Wasted COP). I'll try fully-sequential tomorrow...
Wideband helped me a lot to have a good idle (running semi-sequential and Wasted COP). I'll try fully-sequential tomorrow...
-
- Super MS/Extra'er
- Posts: 855
- Joined: Sun Oct 10, 2010 6:33 am
Re: Toyota 3SGE Beams VVTi code
very good
Re: Toyota 3SGE Beams VVTi code
Need phase change on 2JZ VVTi 4Cyl decoder. The engine didn't start with fully sequential settings.
Many tks for your help AbatelliCristian ;)
Many tks for your help AbatelliCristian ;)
-
- Helpful MS/Extra'er
- Posts: 89
- Joined: Sun Dec 07, 2008 6:05 pm
Re: Toyota 3SGE Beams VVTi code
Did you try 575° as trigger angle?mr2.3sge wrote:Need phase change on 2JZ VVTi 4Cyl decoder. The engine didn't start with fully sequential settings.
Many tks for your help AbatelliCristian ;)
-
- Experienced MS/Extra'er
- Posts: 280
- Joined: Fri Dec 17, 2010 9:13 am
- Location: Leiria - Portugal
Re: Toyota 3SGE Beams VVTi code
That only apply to tooth wheel. He is using a specific trigger wheel, for 2jz.pimp4lyphe wrote:Did you try 575° as trigger angle?mr2.3sge wrote:Need phase change on 2JZ VVTi 4Cyl decoder. The engine didn't start with fully sequential settings.
Many tks for your help AbatelliCristian ;)
-
- Helpful MS/Extra'er
- Posts: 89
- Joined: Sun Dec 07, 2008 6:05 pm
Re: Toyota 3SGE Beams VVTi code
Yeah my bad.
-
- Experienced MS/Extra'er
- Posts: 280
- Joined: Fri Dec 17, 2010 9:13 am
- Location: Leiria - Portugal
Re: Toyota 3SGE Beams VVTi code
No problem, we are learning every daypimp4lyphe wrote:Yeah my bad.
Re: Toyota 3SGE Beams VVTi code
Hi James,
I'm still waiting for changes on 2JZ VVTi 4Cyl decoder.
Many Thanks
I'm still waiting for changes on 2JZ VVTi 4Cyl decoder.
Many Thanks
-
- Site Admin
- Posts: 39585
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Toyota 3SGE Beams VVTi code
Changed for the next dev release.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Site Admin
- Posts: 39585
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Toyota 3SGE Beams VVTi code
Now available.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: Toyota 3SGE Beams VVTi code
It works perfectly ;)Now available.
James
Many Tks.
-
- Super MS/Extra'er
- Posts: 902
- Joined: Mon Jul 07, 2008 5:45 pm
Re: Toyota 3SGE Beams VVTi code
great support!
Re: Toyota 3SGE Beams VVTi code
Will the 2JZ VVTi 4-cylinder mode also work for the 3S-GE black top BEAMS with dual VVTi? The wheel patterns and cam sensors are the same with the exception of the exhaust cam and the same 4-1 pattern on the exhaust cam shaft.
Thanks!
Thanks!
-
- Site Admin
- Posts: 39585
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Toyota 3SGE Beams VVTi code
So long as the crank and intake cam patterns are the same, you will get full RPM-sync. A regular 4-1 pattern on the other cam ought to work ok by enabling a second cam input and selecting 4 teeth.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: Toyota 3SGE Beams VVTi code
Thanks for the reply.
I just checked the settings regarding the VVTi. I was able to select the number of VVTi solenoids to be controlled, but the number of teeth on cam 2 was not selectable.
I just checked the settings regarding the VVTi. I was able to select the number of VVTi solenoids to be controlled, but the number of teeth on cam 2 was not selectable.
-
- Site Admin
- Posts: 39585
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Toyota 3SGE Beams VVTi code
I checked the code. For 4cyl is it always assuming that the cam teeth fall on a 4 tooth pattern.Marc D wrote:Thanks for the reply.
I just checked the settings regarding the VVTi. I was able to select the number of VVTi solenoids to be controlled, but the number of teeth on cam 2 was not selectable.
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: Toyota 3SGE Beams VVTi code
Perfect, that helps a lot. Thanks!