ms3pro no connection
Moderators: jsmcortina, muythaibxr
ms3pro no connection
just installed a ms3 pro and cant get it to connect. Windows xp, serial connection pins 2,3 and 5 strait into ecu. Did the portcheck, nothing, did the loop back test and port 1 passed, port 4 passed,baud rate set at 115200. I have 5volts at vref. Can anyone advise me the next coarse of action?,, thanks in advance.
-
- Super MS/Extra'er
- Posts: 1341
- Joined: Mon Sep 05, 2011 1:20 pm
Re: ms3pro no connection
I had one like that, had to return it to DIY where they replaced the comm chip.
Graduate of EFI University.
I build, repair, install and tune Megasquirt systems in North Dakota and beyond!
I build, repair, install and tune Megasquirt systems in North Dakota and beyond!
-
- Experienced MS/Extra'er
- Posts: 183
- Joined: Wed Mar 19, 2008 2:12 pm
- Location: South Africa
Re: ms3pro no connection
Hi there,,,
Currently sitting with exactly the same prob here...
But mines on a MS3-Pro Module.... Mmmmm wonder if it the same problem?...
Gordon
Currently sitting with exactly the same prob here...
But mines on a MS3-Pro Module.... Mmmmm wonder if it the same problem?...
Gordon
-
- Super MS/Extra'er
- Posts: 1986
- Joined: Sat Jul 22, 2006 8:02 pm
- Location: Eureka, NV USA
- Contact:
Re: ms3pro no connection
Just a random thought..... Are you certain that the serial cable is in fact 'straight through'? Or possibly one that has pins 2 & 3 swapped? Both types will pass loopback!
Ken
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
-
- Super MS/Extra'er
- Posts: 2639
- Joined: Tue Sep 14, 2004 4:17 pm
- Location: Aberdeen, Wa
Re: ms3pro no connection
Or maybe try the USB port? That's all I've used and never had an issue with the style with the rf choke
Volvo 940, 2jzge, MS3Pro, daily
240Z, 2JZ, MS3Pro boost control
240Z, 2JZ, MS3Pro boost control
Re: ms3pro no connection
pins 2,3 and 5 are straight thru, checked that first, I am at loss of what to do next. I had my laptop to a repair shop, they found no issue with serial ports.
-
- Experienced MS/Extra'er
- Posts: 183
- Joined: Wed Mar 19, 2008 2:12 pm
- Location: South Africa
Re: ms3pro no connection
Here on the MS3_Module... Neither work.. RS232 or USB.. I know it's not the cables.. As all the other systems I have here all work.. MS2 Modules & MS3-Pro_modules..
-
- Super MS/Extra'er
- Posts: 1341
- Joined: Mon Sep 05, 2011 1:20 pm
Re: ms3pro no connection
Yeah, mine was an MS3Pro module as well. All my microsquirt modules worked fine and the other MS3Pro modules I've worked with were fine but that one was dead, both USB and serial. Matt had it for weeks testing it until he replaced the comm chip and all was good again. I would contact DIY for a RMA number.
Graduate of EFI University.
I build, repair, install and tune Megasquirt systems in North Dakota and beyond!
I build, repair, install and tune Megasquirt systems in North Dakota and beyond!
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: ms3pro no connection
MS3-Pro modules ship with no firmware - have you loaded it yet?phoenix3d wrote:Hi there,,,
Currently sitting with exactly the same prob here...
But mines on a MS3-Pro Module.... Mmmmm wonder if it the same problem?...
Gordon
Matt Cramer -1966 Dodge Dart slant six running on MS3X
Re: ms3pro no connection
yes I tried to load firmware, will not connect to do that. I have no issue connecting with my wideband, it picks up com1 without problem.
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: ms3pro no connection
Have you tried both USB and serial?
Matt Cramer -1966 Dodge Dart slant six running on MS3X
Re: ms3pro no connection
I have not, I would need to purchase a usb to serial adapter. The serial port works just fine as it will connect with my wideband controller.
-
- Site Admin
- Posts: 39621
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: ms3pro no connection
The MS3-Pro has a USB-serial adapter built-in. You'd need to provide a socket and cable.chilly wrote:I have not, I would need to purchase a usb to serial adapter.
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: ms3pro no connection
Just a thought. ... but have you tried going into "settings" in TunerStudio and see what "COM" port it's set at? I encountered this problem just yesterday. ... and I found that TS settings was changed... I usually run mine on COM4 and for some reason it was set at COM3....
Just try and double check your settings on "Project Properties " in TS and see which Port COM is designated. .... hopefully this helps.
Tim
Just try and double check your settings on "Project Properties " in TS and see which Port COM is designated. .... hopefully this helps.
Tim
Re: ms3pro no connection
I can not get the firmware to load, that would be the first step,, correct?,, tuner studio is set to com1, when I select new project it will does not detect a com port, when I try to load firmware it does not detect a port or ecu, I have 5volts at vref, the ecu is powered, my com cable is wired direct to ecu, it passes loopback on com1 no issue.I have gone thru the troubleshooting like the manual says.
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: ms3pro no connection
Try putting the boot jumper in place and running Port Check. Post a screen shot of what happens.
Matt Cramer -1966 Dodge Dart slant six running on MS3X
Re: ms3pro no connection
I had tuner studio open then tried to load firmware, it flagged com1 as busy, its the only time its showed a com at all.
Re: ms3pro no connection
Sounds similar to what I am facing with MS3Pro-Module, has this post been fixed? What solution did you use?
Cheers,
Tony.
Cheers,
Tony.
Volvo 122 B234f+t- Microsquirt, Volvo 244 B230f+t-MS1Extra, Volvo 940 1UZ-FE +turbo - MS3X, Toyota LC80 1FZ-FE - MS2Extra v3.0