Hello,
I want to install one real clock module on my MS3 card , I do not find the documentation to perform the work. I only find for the MS3X expansion board.
Can you help me?
RTC installation instruction for MS3.
Moderators: jsmcortina, muythaibxr
-
- Site Admin
- Posts: 39619
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: RTC installation instruction for MS3.
The RTC module is designed to be installed on the MS3X card.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: RTC installation instruction for MS3.
Hello.
But, i read this note in diyautotune web site:
This module is intended exclusively for the MS3 and is considerably easier to install if used with an MS3X expansion board.
Note: If you are ordering the real time clock module with an assembled MS3, we can install it in the MS3 for an extra $15 charge.
If i understand, the module can be installed on a MS3 without expansion board?
Thanks
But, i read this note in diyautotune web site:
This module is intended exclusively for the MS3 and is considerably easier to install if used with an MS3X expansion board.
Note: If you are ordering the real time clock module with an assembled MS3, we can install it in the MS3 for an extra $15 charge.
If i understand, the module can be installed on a MS3 without expansion board?
Thanks
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: RTC installation instruction for MS3.
Installing it without the MS3X will require matching up the holes that the RTCC would mount in to wires connected to the 34 pin header on the MS3 daughter board. This chart shows which RTCC mounting hole goes to which pin on the 34 pin header.Rotxam wrote:Hello.
But, i read this note in diyautotune web site:
This module is intended exclusively for the MS3 and is considerably easier to install if used with an MS3X expansion board.
Note: If you are ordering the real time clock module with an assembled MS3, we can install it in the MS3 for an extra $15 charge.
If i understand, the module can be installed on a MS3 without expansion board?
Thanks
H1 - 29
H2 - 27
H3 - 22
H4 - 20
H5 - 31
H6 - 30
See this image for reference for where the holes go:
Matt Cramer -1966 Dodge Dart slant six running on MS3X
Re: RTC installation instruction for MS3.
Thank you for your reply Mr. Cramer.
So, if I understand, this 4 holes , GND, 5V, SDA and SCL, connect to the pin 30, 31, 20 and 22.
This is OK?
Thanks
So, if I understand, this 4 holes , GND, 5V, SDA and SCL, connect to the pin 30, 31, 20 and 22.
This is OK?
Thanks
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: RTC installation instruction for MS3.
Yes.
Matt Cramer -1966 Dodge Dart slant six running on MS3X