Lost gauge options going from MS3 Pre1.3 Beta 12 to Pre 1.3.
Moderators: jsmcortina, muythaibxr
Lost gauge options going from MS3 Pre1.3 Beta 12 to Pre 1.3.
I no longer can select fuel pressure as one of my gauges. Not sure where the hangup is, but it would be great to have. Had a fuel hose tear inside the fuel tank last week, and the fuel pressure gauge option would have shown me the problem immediately.
Last edited by hardline on Wed May 28, 2014 11:40 am, edited 1 time in total.
2000 ZX2 : Sequential COP, MS3 + MS3X + TinyIOx, PWM Returnless Fuel, Flex Fuel, Variable Geometry Intake Manifold, Garrett GTX2863R .82AR housing @ 15 psi
Re: Lost gauge options going from MS3 Pre1.3 to Beta 1.3
Sorry, should have mentioned this is in ShadowDash
2000 ZX2 : Sequential COP, MS3 + MS3X + TinyIOx, PWM Returnless Fuel, Flex Fuel, Variable Geometry Intake Manifold, Garrett GTX2863R .82AR housing @ 15 psi
-
- Site Admin
- Posts: 39615
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Lost gauge options going from MS3 Pre1.3 to Beta 1.3
I don't understand your question, did you change MS3 firmware version? If so, from what, to what. Please be precise with version numbers.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: Lost gauge options going from MS3 Pre1.3 to Beta 1.3
Went from pre 1.3.0 beta 12 to pre 1.3.1 beta 4
2000 ZX2 : Sequential COP, MS3 + MS3X + TinyIOx, PWM Returnless Fuel, Flex Fuel, Variable Geometry Intake Manifold, Garrett GTX2863R .82AR housing @ 15 psi
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Lost gauge options going from MS3 Pre1.3 Beta 12 to Pre
I'm betting it was because I did not have the latest beta ini on the server.. It is out there, reconnect while your tablet/phone is connected to the internet and it should find the update.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Re: Lost gauge options going from MS3 Pre1.3 Beta 12 to Pre
That worked, thanks
2000 ZX2 : Sequential COP, MS3 + MS3X + TinyIOx, PWM Returnless Fuel, Flex Fuel, Variable Geometry Intake Manifold, Garrett GTX2863R .82AR housing @ 15 psi