Feature request TCC Lockup curve
Moderators: jsmcortina, muythaibxr
Feature request TCC Lockup curve
Hi James,
Is it possible to create a TCC lockup curve based on load and speed? Or is the feature already there? Thanks.
Doddy
Is it possible to create a TCC lockup curve based on load and speed? Or is the feature already there? Thanks.
Doddy
-
- Site Admin
- Posts: 39613
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Feature request TCC Lockup curve
It isn't there already, there are TPS, RPM and VSS thresholds.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: Feature request TCC Lockup curve
Hi James,
I just found this issue last week when I was on the dyno. I set the TCC lockup speed to 200kph so it wont engage during dyno but it still engage at 50. So I set the max TPS value to 0%. 50kph was the speed I set for 3rd gear in lockup each gear setting. Is this normal? Thanks.
Regards,
Doddy
My hardware are MS3pro with prealpha7 and GPIO with trans firmware 028
I just found this issue last week when I was on the dyno. I set the TCC lockup speed to 200kph so it wont engage during dyno but it still engage at 50. So I set the max TPS value to 0%. 50kph was the speed I set for 3rd gear in lockup each gear setting. Is this normal? Thanks.
Regards,
Doddy
My hardware are MS3pro with prealpha7 and GPIO with trans firmware 028
-
- Site Admin
- Posts: 39613
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Feature request TCC Lockup curve
Do you have a datalog of that?
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: Feature request TCC Lockup curve
Nope. I'll take a datalog next time I drive the car.
Doddy
Doddy
Re: Feature request TCC Lockup curve
James,
Here is the datalog and msq. Thanks.
Doddy
Here is the datalog and msq. Thanks.
Doddy
-
- Site Admin
- Posts: 39613
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Feature request TCC Lockup curve
The "Lockup speed" in the top left is no longer used. Only the RPMs/VSSs to the right are used.
The next release (in a few minutes) will have that rogue setting removed from the screen.
James
The next release (in a few minutes) will have that rogue setting removed from the screen.
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".