JBPerf Exspansion Boards

A forum for discussing the MegaSquirt related (but non-B&G) board development, assembly, installation, and testing.

Moderators: jsmcortina, muythaibxr

JBPerf Exspansion Boards

Postby KenK » Tue Oct 10, 2017 8:13 am

I'm looking to get another 4-channel Driver board from JBPerf. I need the board with all of the components included.

How would I go about getting one??

Ken
KenK
Helpful MS/Extra'er
 
Posts: 46
Joined: Wed Jan 13, 2016 12:02 pm

Re: JBPerf Exspansion Boards

Postby kjones6039 » Tue Oct 10, 2017 8:25 am

KenK wrote:I'm looking to get another 4-channel Driver board from JBPerf. I need the board with all of the components included.

How would I go about getting one??

Ken

Perhaps order it from JBPerf, or are they out of stock? Exactly which board are you looking for? IIRC, I probably have 1 or 2 lying around.

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
User avatar
kjones6039
Super MS/Extra'er
 
Posts: 1817
Joined: Sat Jul 22, 2006 8:02 pm
Location: Eureka, NV USA

Re: JBPerf Exspansion Boards

Postby KenK » Tue Oct 10, 2017 9:09 am

I went to the JBPerf website this morning and there are no "Buy" buttons.

I saw a post where Jean stated that he had pulled the "buy" buttons from all of his products on his website.

The board I want is a 4-channel driver board setup to drive four (4) high impedance injectors.

Ken
KenK
Helpful MS/Extra'er
 
Posts: 46
Joined: Wed Jan 13, 2016 12:02 pm

Re: JBPerf Exspansion Boards

Postby racingmini_mtl » Tue Oct 10, 2017 10:06 am

Some of the boards are available at this time but not the 4-channel driver board. The issue is that I don't have everything in stock and I also cannot spend the time needed to make sure all orders would be filled so I only keep available on the site what I know will be delivered in a timely manner (a few business days).

Jean
jbperf.com Main site . . . . . . . . . . . . . . . . . . . . . . jbperf.com Forum
Image
racingmini_mtl
Super MS/Extra'er
 
Posts: 7919
Joined: Sun May 02, 2004 6:51 am
Location: Quebec, Canada

Re: JBPerf Exspansion Boards

Postby KenK » Wed Oct 11, 2017 6:35 am

I hate to be a pain Jean but. is the problem with the 4 channel driver board the board or the components?

I you have the board, I can get the component myself as long as I know what they are.

If you don't have the board itself, can I get a schematic from you showing the circuit. I can perfboard the necessary wiring as well as get the necessary components again as long as I know what they are.

Hope things are well with you.

Ken
KenK
Helpful MS/Extra'er
 
Posts: 46
Joined: Wed Jan 13, 2016 12:02 pm

Re: JBPerf Exspansion Boards

Postby lotus23C » Fri Oct 13, 2017 11:06 pm

Actually, I could do with one of those boards as well.
Currently Lotus 23C replica Audi 1.8T MS 2 v3 Sequential COP and ignition.
Lotus 7 replica 4age 20V blacktop MS2 v3
lotus23C
Helpful MS/Extra'er
 
Posts: 118
Joined: Sun Apr 22, 2012 1:20 am
Location: New Zealand


Return to Expansion boards

Who is online

Users browsing this forum: No registered users and 1 guest