I'm looking to get another 4-channel Driver board from JBPerf. I need the board with all of the components included.
How would I go about getting one??
Ken
JBPerf Exspansion Boards
Moderators: jsmcortina, muythaibxr
-
- Super MS/Extra'er
- Posts: 1986
- Joined: Sat Jul 22, 2006 8:02 pm
- Location: Eureka, NV USA
- Contact:
Re: JBPerf Exspansion Boards
Perhaps order it from JBPerf, or are they out of stock? Exactly which board are you looking for? IIRC, I probably have 1 or 2 lying around.KenK wrote:I'm looking to get another 4-channel Driver board from JBPerf. I need the board with all of the components included.
How would I go about getting one??
Ken
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
Re: JBPerf Exspansion Boards
I went to the JBPerf website this morning and there are no "Buy" buttons.
I saw a post where Jean stated that he had pulled the "buy" buttons from all of his products on his website.
The board I want is a 4-channel driver board setup to drive four (4) high impedance injectors.
Ken
I saw a post where Jean stated that he had pulled the "buy" buttons from all of his products on his website.
The board I want is a 4-channel driver board setup to drive four (4) high impedance injectors.
Ken
-
- Super MS/Extra'er
- Posts: 9130
- Joined: Sun May 02, 2004 6:51 am
- Location: Quebec, Canada
- Contact:
Re: JBPerf Exspansion Boards
Some of the boards are available at this time but not the 4-channel driver board. The issue is that I don't have everything in stock and I also cannot spend the time needed to make sure all orders would be filled so I only keep available on the site what I know will be delivered in a timely manner (a few business days).
Jean
Jean
Re: JBPerf Exspansion Boards
I hate to be a pain Jean but. is the problem with the 4 channel driver board the board or the components?
I you have the board, I can get the component myself as long as I know what they are.
If you don't have the board itself, can I get a schematic from you showing the circuit. I can perfboard the necessary wiring as well as get the necessary components again as long as I know what they are.
Hope things are well with you.
Ken
I you have the board, I can get the component myself as long as I know what they are.
If you don't have the board itself, can I get a schematic from you showing the circuit. I can perfboard the necessary wiring as well as get the necessary components again as long as I know what they are.
Hope things are well with you.
Ken
-
- Helpful MS/Extra'er
- Posts: 130
- Joined: Sun Apr 22, 2012 1:20 am
- Location: New Zealand
- Contact:
Re: JBPerf Exspansion Boards
Actually, I could do with one of those boards as well.
Currently Lotus 23C replica Audi 1.8T MS 2 v3 Sequential COP and ignition.
Lotus 7 replica 4age 20V blacktop MS2 v3
Lotus 7 replica 4age 20V blacktop MS2 v3