JEEP CHEROKEE 2000
Moderators: jsmcortina, muythaibxr
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: JEEP CHEROKEE 2000
You could check the CAS with a volt meter while turning the engine with a wrench or breaker bar.
Matt Cramer -1966 Dodge Dart slant six running on MS3X
Re: JEEP CHEROKEE 2000
Hi, i have a question . I have an msI cpu and would like to know if there is a code already done for this cpu to manage this weel, or we have to do the same job ?
thanks
thanks
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: JEEP CHEROKEE 2000
No, there's no special code in the MS1 to decode that wheel.
If you could arrange a single tooth cam trigger, the "dumb" MS1 code could work ok with the crank wheel.
But the existing pattern - no.
James
If you could arrange a single tooth cam trigger, the "dumb" MS1 code could work ok with the crank wheel.
But the existing pattern - no.
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: JEEP CHEROKEE 2000
Anyone got the angles yet? Post NOW and this pattern can be in the next JimStim code release.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: JEEP CHEROKEE 2000
Looks like this is the wheel pattern - but no angles = no code.
JamesI can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: JEEP CHEROKEE 2000
That's definitely not a 2000 4.0 trigger wheel pattern. I think that first appeared in the 2002 Jeep Liberty with the 3.7 V6 and may not have lasted for very long before the NGC wheels appeared.
I'm going to see if I can get the numbers off a FSM drawing by measuring it with a ruler. I was trying to avoid this as I'm not sure how accurate they are, but here goes.
Crank sensor rising edge, starting at zero degrees: 98 104 110 116 - 218 224 230 236 - 338 344 350 356
Cam sensor: A 180 degree ring (360 crank degrees). Not sure exactly where it syncs up, and it looks as if the sensor could be rotated 360 degrees in its housing while adjusting it.
I'm going to see if I can get the numbers off a FSM drawing by measuring it with a ruler. I was trying to avoid this as I'm not sure how accurate they are, but here goes.
Crank sensor rising edge, starting at zero degrees: 98 104 110 116 - 218 224 230 236 - 338 344 350 356
Cam sensor: A 180 degree ring (360 crank degrees). Not sure exactly where it syncs up, and it looks as if the sensor could be rotated 360 degrees in its housing while adjusting it.
Matt Cramer -1966 Dodge Dart slant six running on MS3X
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: JEEP CHEROKEE 2000
Looks more like 20 degrees between the main crank slots not 6 ?
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: JEEP CHEROKEE 2000
That's why I was trying to avoid measuring the FSM drawing; I didn't trust it. I know the 116, 236, and 356 degree triggers are accurate as the FSM wrote out that each group is 120 degrees apart and the 356 degree position. If they're 20 degrees apart, which looks reasonable from the flywhee, it would work out to this:
56 76 96 116 - 176 196 216 236 - 296 316 336 356
Looking back at the pictures, these values look a lot more reasonable.
56 76 96 116 - 176 196 216 236 - 296 316 336 356
Looking back at the pictures, these values look a lot more reasonable.
Matt Cramer -1966 Dodge Dart slant six running on MS3X
-
- MS/Extra Newbie
- Posts: 16
- Joined: Sat Jun 18, 2005 1:44 pm
Re: JEEP CHEROKEE 2000
It would be great if someone could get this set-up to work with MS, keep up the good work! I'm planning to buy a 4.0 XJ in about 6 months and was wanting to put MS on it and this would simplify it
Re: JEEP CHEROKEE 2000
Hi friends. i have the answer.
the weel have 1080 milimeters of circunference
350 milimeters of diameter
175 milimeters of ratio
60 milimeters between the notchs. so we can put 18 segments of 20 degre each
so we have 20 degre
the weel have 1080 milimeters of circunference
350 milimeters of diameter
175 milimeters of ratio
60 milimeters between the notchs. so we can put 18 segments of 20 degre each
so we have 20 degre
Re: JEEP CHEROKEE 2000
Hi friends. i have the answer.
the weel have 1080 milimeters of circunference
350 milimeters of diameter
175 milimeters of ratio
60 milimeters between the notchs. so we can put 18 segments of 20 degrees each
so we have 20 degrees
the weel have 1080 milimeters of circunference
350 milimeters of diameter
175 milimeters of ratio
60 milimeters between the notchs. so we can put 18 segments of 20 degrees each
so we have 20 degrees
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: JEEP CHEROKEE 2000
Thanks for confirming that, gsune!
Matt Cramer -1966 Dodge Dart slant six running on MS3X
Re: JEEP CHEROKEE 2000
Hi there. did anyone already make the code for this weel ????
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: JEEP CHEROKEE 2000
It was too late in the 2.1.0 release cycle to add this wheel.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: JEEP CHEROKEE 2000
Hi, when will be the next release?
thanks
thanks
Re: JEEP CHEROKEE 2000
Hi, when will be the next release?
thanks
thanks
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: JEEP CHEROKEE 2000
I haven't looked into adding this wheel yet.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: JEEP CHEROKEE 2000
Hey guys I am still waiting...
I will be patient
so do not worry
thanks
I will be patient
so do not worry
thanks
-
- Master MS/Extra'er
- Posts: 606
- Joined: Sat Apr 11, 2009 12:54 pm
- Location: Aalsmeer the netherlands
- Contact:
Re: JEEP CHEROKEE 2000
you are a patient man
but why not start with a 36-1 or 60-2 wheel
just a thought
but why not start with a 36-1 or 60-2 wheel
just a thought
Re: JEEP CHEROKEE 2000
Hi there
i still waiting...
i still waiting...