MS2Extra 3.4.x Duty Based Staging Not Working?
Moderators: jsmcortina, muythaibxr
-
- Experienced MS/Extra'er
- Posts: 183
- Joined: Wed Mar 19, 2008 2:12 pm
- Location: South Africa
MS2Extra 3.4.x Duty Based Staging Not Working?
Hi James.
As posted before under 3.4.2 beta 2 posts.
Please note we have come across a situation whereby the "DUTY" Base staged injection is not functioning.
This is occurring in both Batch and Semi Sequential based staging, Notably on uS Module that we're using, as we do not run the Std MS2 setups.
Hardware used is uS Module with additional hardware for Seq Fuel (PT6 & PT7) & Spark outputs (WLED & ALED).
Attached are some example MSL's of the Staging not working with DUTY based, as well as staging that is working using MAP based. So Staging in general is working but not under Duty Based
We try activating Staging via a value of 80% Duty (although we tried other values as well).
Thanks You.
working MAP Based examples to follow.
As posted before under 3.4.2 beta 2 posts.
Please note we have come across a situation whereby the "DUTY" Base staged injection is not functioning.
This is occurring in both Batch and Semi Sequential based staging, Notably on uS Module that we're using, as we do not run the Std MS2 setups.
Hardware used is uS Module with additional hardware for Seq Fuel (PT6 & PT7) & Spark outputs (WLED & ALED).
Attached are some example MSL's of the Staging not working with DUTY based, as well as staging that is working using MAP based. So Staging in general is working but not under Duty Based
We try activating Staging via a value of 80% Duty (although we tried other values as well).
Thanks You.
working MAP Based examples to follow.
-
- Experienced MS/Extra'er
- Posts: 183
- Joined: Wed Mar 19, 2008 2:12 pm
- Location: South Africa
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
Additional MSL of MAP Based staging that's Good. (For reference)
Thank you.
Thank you.
-
- Super MS/Extra'er
- Posts: 9130
- Joined: Sun May 02, 2004 6:51 am
- Location: Quebec, Canada
- Contact:
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
You don't have the correct number of squirts for a semi-sequential setup. It should be 2/sim (or 4/alt). With the wrong value, the duty cycle is not correctly computed internally which is why staging won't work properly.
Jean
Jean
-
- Experienced MS/Extra'er
- Posts: 183
- Joined: Wed Mar 19, 2008 2:12 pm
- Location: South Africa
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
Hi Jean..
ok... So semi-seq staging with my current settings no good... Cool.. I'll double check
What about the Batch Based Staging... it also didn't work.. or am I missing something there as well?
If there is a problem that it won't calculate correctly at 1 squirt, could someone please UPDATE the Tooltips etc. in the ini file and LET Everyone know, as grenading a $20K engine is an expensive way to find out.
Kindest Regards
Gordon.
ok... So semi-seq staging with my current settings no good... Cool.. I'll double check
What about the Batch Based Staging... it also didn't work.. or am I missing something there as well?
If there is a problem that it won't calculate correctly at 1 squirt, could someone please UPDATE the Tooltips etc. in the ini file and LET Everyone know, as grenading a $20K engine is an expensive way to find out.
Kindest Regards
Gordon.
-
- Super MS/Extra'er
- Posts: 4122
- Joined: Fri May 07, 2004 3:33 am
- Location: Australia
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
I don't know how your duty staging will work in reality, even if it did trigger properly.
I saw on the MSQ you had 85% duty staging with 5% hysteresis. I have 630cc primaries and 630cc secondaries and I stage from TPS and MAP. When I stage my PW and Duty both halve in about 0.1S. That is usually dropping from something like 60% duty to 30% duty from my 50/50 injector split. You have a 40/60 split so from 85% duty I would expect you to drop into the low 40% on staging. I do not think 5% hysteresis is going to work when you drop 40+.
I have had no issues with using TPS primary and Map secondary staging.
I saw on the MSQ you had 85% duty staging with 5% hysteresis. I have 630cc primaries and 630cc secondaries and I stage from TPS and MAP. When I stage my PW and Duty both halve in about 0.1S. That is usually dropping from something like 60% duty to 30% duty from my 50/50 injector split. You have a 40/60 split so from 85% duty I would expect you to drop into the low 40% on staging. I do not think 5% hysteresis is going to work when you drop 40+.
I have had no issues with using TPS primary and Map secondary staging.
Find the Manuals up top under Quick links: Manuals.
Cheers Luke
Cheers Luke
-
- Site Admin
- Posts: 8230
- Joined: Thu Oct 14, 2004 12:48 pm
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
Duty-based staging uses the calculated primary duty without the stage to determine if it should stay staged. It will work fine.
Megasquirt is not for use on pollution controlled vehicles. Any advice I give is for off road use only.
-
- Super MS/Extra'er
- Posts: 4122
- Joined: Fri May 07, 2004 3:33 am
- Location: Australia
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
Ah good to know, I thought it was real duty.
Find the Manuals up top under Quick links: Manuals.
Cheers Luke
Cheers Luke
-
- Experienced MS/Extra'er
- Posts: 183
- Joined: Wed Mar 19, 2008 2:12 pm
- Location: South Africa
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
Hi Guys...
Yep to confirm as Jean said...
DUTY Staging DOES NOT work with 1 Squirt per cycle...
in either Batch or Semi-Seq...
Tried it on the bench..
Now how would we work around the LARGE injector pulsewidth problem at 2 Squirts...
Actual Injector sizes running on the vehicle are 900cc Primaries & 1600cc Secondary. Full 100% (98% actual) Ethanol @ 2.6Bar Boost..
Thanks Jean.. & Slow_Hemi6 for your assistance!
PS.. I never even thought that the Squirts/cycle would be an issue, pity though... Maybe something to look at in the pipeline.
Gordon.
Yep to confirm as Jean said...
DUTY Staging DOES NOT work with 1 Squirt per cycle...
in either Batch or Semi-Seq...
Tried it on the bench..
Now how would we work around the LARGE injector pulsewidth problem at 2 Squirts...
Actual Injector sizes running on the vehicle are 900cc Primaries & 1600cc Secondary. Full 100% (98% actual) Ethanol @ 2.6Bar Boost..
Thanks Jean.. & Slow_Hemi6 for your assistance!
PS.. I never even thought that the Squirts/cycle would be an issue, pity though... Maybe something to look at in the pipeline.
Gordon.
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
It is a shame you didn't post up the MSQ/MSL a few weeks back before 3.4.2 was released.
Investigating, it looks like the code has behaved like this for over five years ?? (3.0.x firmware)
James
Investigating, it looks like the code has behaved like this for over five years ?? (3.0.x firmware)
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
Wasn't there some talk, waayyy some time ago, about changing the code etc to basically ignore the 'alt/simult' and 'number of squirts' settings for seq and semi-seq, since the only valid options are '1' and '2' respectively, and 'simultaneous' in both cases?
Temporarily shut down - back soon!
QuadraMAP Sensor Module -- PWM-to-Stepper Controller -- Dual Coil Driver
Coming soon: OctoMAP Sensor Module
TTR Ignition Systems
QuadraMAP Sensor Module -- PWM-to-Stepper Controller -- Dual Coil Driver
Coming soon: OctoMAP Sensor Module
TTR Ignition Systems
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
MS3 handles this differently. However, as MS2/Extra is now at a mature stage in its life, I am reluctant to make a change like that when the code is overall known to be working well.dontz125 wrote:Wasn't there some talk, waayyy some time ago, about changing the code etc to basically ignore the 'alt/simult' and 'number of squirts' settings for seq and semi-seq
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
I've made a fix and am just working with Jean on some tooltip enhancements for semi-seq before I put out a new beta.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Experienced MS/Extra'er
- Posts: 183
- Joined: Wed Mar 19, 2008 2:12 pm
- Location: South Africa
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
AWESOME!!!!
Thanks James!!..
Thanks James!!..
Re: MS2Extra 3.4.x Duty Based Staging Not Working?
Done some bench testing of the Staged feature in MS2 extra 3.4.2 now, and also tried the 3.4.3 Beta, trying to figure out how this stuff works before settings it up on my new drag race engine.
I have found that the "Table" does not work in semi sequential mode while using additional drivers.
PW#1 does what it's supposed to do, and the same with PW#3 & 4 (secondary injectors), but PW#2 tracks the PW#3 & 4 values instead of PW#1.
They alternate as they should though, and it all works fine in the other modes such as RPM, TPS, MAP etc, and also when in 0 and 100% in table mode, just not any value in between. This renders the table function useless in this particular case.
And another thing I find a bit weird: Since MS2 only have two DC% indicators (DC1 and DC2), would it not be logical that DC%#1 is for PW1/2 (primary injectors), and DC%#2 would be for PW3/4 when running additional drivers in staged mode?
The attached pic. shows what I'm talking about when in table mode running additional drivers and semi-sequential and the table cells are set to a value != to 0 || 100.
I have found that the "Table" does not work in semi sequential mode while using additional drivers.
PW#1 does what it's supposed to do, and the same with PW#3 & 4 (secondary injectors), but PW#2 tracks the PW#3 & 4 values instead of PW#1.
They alternate as they should though, and it all works fine in the other modes such as RPM, TPS, MAP etc, and also when in 0 and 100% in table mode, just not any value in between. This renders the table function useless in this particular case.
And another thing I find a bit weird: Since MS2 only have two DC% indicators (DC1 and DC2), would it not be logical that DC%#1 is for PW1/2 (primary injectors), and DC%#2 would be for PW3/4 when running additional drivers in staged mode?
The attached pic. shows what I'm talking about when in table mode running additional drivers and semi-sequential and the table cells are set to a value != to 0 || 100.
- Attachments
-
- Staged table additional drivers semi-seq.jpg (312.83 KiB) Viewed 1062 times