In the MS2/3.57 Hardware manual, http://www.msextra.com/doc/pdf/MS2V357_Hardware-3.4.pdf there are lots of references throughout the ignition section to "build the circuit in 5.3.0.3" -- except that there is no section 5.3.0.3. I think they mean 5.3.1.3 ??
Also, I want to make sure I'm understanding this correctly.. In 5.3.1.4, there's a table showing Spark A/B/C being available on PAD 1/3/2. "The PAD1,2,3 connections should be jumpered to an output pin of choice (e.g. SPR3) and can drive many logic coils." -- so if jumper PAD1--> SPR3 PAD3 --> SPR4, then I can directly hookup the SPR3/SPR4wires on my DB37 to the VAG 032 905 106B wasted spark logic coil? (shown on page 83)
Thanks,
-Dave
3.57 Documentation correction, question
Moderators: jsmcortina, muythaibxr
-
- Master MS/Extra'er
- Posts: 786
- Joined: Sun May 02, 2004 5:55 pm
- Location: Cleveland, Ohio
- Contact:
3.57 Documentation correction, question
'70 Chevelle ZZ383/700r4/3.73 MS3X, 36-1, LS Coils, Holley Stealthram -- success story
'92 Saturn 1.9 DOHC/5sp, MS3, Champcar racer success story
'79 Malibu DartSHP400/80mm/PG/3.55, MS3X/36-1/LS Coils -- success story
Porsche 944 S2 3.0 -- MS3X/36-1/LS Coils, 1:44s Mid-Ohio, Pro Course
'92 Saturn 1.9 DOHC/5sp, MS3, Champcar racer success story
'79 Malibu DartSHP400/80mm/PG/3.55, MS3X/36-1/LS Coils -- success story
Porsche 944 S2 3.0 -- MS3X/36-1/LS Coils, 1:44s Mid-Ohio, Pro Course
-
- MS/Extra Newbie
- Posts: 7
- Joined: Tue Jan 22, 2019 7:07 am
Re: 3.57 Documentation correction, question
Dear Dave,ChevelleFan wrote:In the MS2/3.57 Hardware manual, http://www.msextra.com/doc/pdf/MS2V357_Hardware-3.4.pdf there are lots of references throughout the ignition section to "build the circuit in 5.3.0.3" -- except that there is no section 5.3.0.3. I think they mean 5.3.1.3 ??
Also, I want to make sure I'm understanding this correctly.. In 5.3.1.4, there's a table showing Spark A/B/C being available on PAD 1/3/2. "The PAD1,2,3 connections should be jumpered to an output pin of choice (e.g. SPR3) and can drive many logic coils." -- so if jumper PAD1--> SPR3 PAD3 --> SPR4, then I can directly hookup the SPR3/SPR4wires on my DB37 to the VAG 032 905 106B wasted spark logic coil? (shown on page 83)
Thanks,
-Dave
Did you receive an answer? I'm interested because I have the exact same question!
Thanks in advance!
-
- Super MS/Extra'er
- Posts: 1978
- Joined: Wed Apr 15, 2009 11:31 am
- Location: Oxford, PA
- Contact:
Re: 3.57 Documentation correction, question
The led pads will drive the vag 4 tower coil without an issue.