Youtube videos, I need people to subscribe

A general forum and a place for initial or prospective users. See Manuals/Documentation
Click here to enter
Contact a Forum Administrator
If unsure where to post, post in this sub-forum.

Moderators: jsmcortina, muythaibxr

whittlebeast
Super MS/Extra'er
Posts: 2221
Joined: Tue May 04, 2004 8:20 pm
Location: St Louis
Contact:

Re: Youtube videos, I need people to subscribe

Post by whittlebeast »

I posted a couple of new videos you guys may like. One is on cam and crank sensors.

https://www.youtube.com/watch?v=weiGhCvcXX8

And the other is about the optional field named MAPxRPM

https://www.youtube.com/watch?v=MJ1V0A9uKLE

Have fun tuning. Andy
Suprazz
Master MS/Extra'er
Posts: 499
Joined: Mon Jan 22, 2007 7:58 pm
Contact:

Re: Youtube videos, I need people to subscribe

Post by Suprazz »

Few suggestions:
You should really use a windows recording software. Your video quality would be much better.

Also, when you make new video. You should but them online at a steady rate (like one per day max or every few days or every weeks).

Thanks for doing this. Great stuff.
Best looking and most advanced CAN-bus gauge
Toyota Supra 7MGE, 7M-GTE and 1JZ-GTE Plug and play ECUs: http://www.perfecttuning.net
Serial to Bluetooth or Serial to WiFi
DIYAutotune Canadian, EFI Source and ECUMaster reseller!
whittlebeast
Super MS/Extra'er
Posts: 2221
Joined: Tue May 04, 2004 8:20 pm
Location: St Louis
Contact:

Re: Youtube videos, I need people to subscribe

Post by whittlebeast »

I have not found laptop SW that will work with my BT headset and my video card on my laptop. I am using an HP Envy X360.

I am off Tuesdays and Fridays. I try to do three on days I am off. As I get to more complicated subjects, it will be harder to keep up the pace.

Last, if I get to the point of making some money with this, I hope to get a better camera. Right now I am using a Samsung S8.

Andy
Motoren
Helpful MS/Extra'er
Posts: 69
Joined: Wed Aug 02, 2017 3:24 pm

Re: Youtube videos, I need people to subscribe

Post by Motoren »

Subscribed :) keep up the good work :)

I'm kinda new to ms software so it's really good with some education videos :)

Kent
Kent
Supra mk3 2jz-gte
Ms3pro ultimate (installing)
Microsquirt trans control (installing)
Denmark
Suprazz
Master MS/Extra'er
Posts: 499
Joined: Mon Jan 22, 2007 7:58 pm
Contact:

Re: Youtube videos, I need people to subscribe

Post by Suprazz »

check for camstasia studio
Best looking and most advanced CAN-bus gauge
Toyota Supra 7MGE, 7M-GTE and 1JZ-GTE Plug and play ECUs: http://www.perfecttuning.net
Serial to Bluetooth or Serial to WiFi
DIYAutotune Canadian, EFI Source and ECUMaster reseller!
whittlebeast
Super MS/Extra'er
Posts: 2221
Joined: Tue May 04, 2004 8:20 pm
Location: St Louis
Contact:

Re: Youtube videos, I need people to subscribe

Post by whittlebeast »

I posted a new video

https://youtu.be/B0Ewmc-51zE

This motor was tuned on the fuel side with MLV HD and VEA

Andy
whittlebeast
Super MS/Extra'er
Posts: 2221
Joined: Tue May 04, 2004 8:20 pm
Location: St Louis
Contact:

Re: Youtube videos, I need people to subscribe

Post by whittlebeast »

I just posted a new video demonstrating some of the capabilities of MLV HD

https://www.youtube.com/watch?v=CG_kY3K_2AE

Andy
whittlebeast
Super MS/Extra'er
Posts: 2221
Joined: Tue May 04, 2004 8:20 pm
Location: St Louis
Contact:

Re: Youtube videos, I need people to subscribe

Post by whittlebeast »

I just posted a video about setting your base timing the first time

https://www.youtube.com/watch?v=d3kDIW93mCY
ninerwfo
MS/Extra Newbie
Posts: 7
Joined: Mon Nov 27, 2017 5:08 pm

Re: Youtube videos, I need people to subscribe

Post by ninerwfo »

Hi Andy, new subscriber to your channel here, and complete newb to this forum. Your timing could not be better - I am just about to first start my forged MX5 (miata) over here in Australia :)
Cheers.
panel
Master MS/Extra'er
Posts: 663
Joined: Tue Aug 17, 2004 9:56 pm
Location: Victoria B.C. Canada
Contact:

Re: Youtube videos, I need people to subscribe

Post by panel »

CanadianDuster wrote: Your list is extensive and I'm waiting patiently. :D

Setting Lambda delay table in TS. How to make that work.
Andy , have you looked into this one yet ?
'65 VW Bus with a Subaru EJ20 Turbo conversion , Air to water I/C , LS coils , 14Point7 Spartan 2 & Solid Air Fuel Ratio 52mm gauge.
MS2 Extra V3.0 board
whittlebeast
Super MS/Extra'er
Posts: 2221
Joined: Tue May 04, 2004 8:20 pm
Location: St Louis
Contact:

Re: Youtube videos, I need people to subscribe

Post by whittlebeast »

Not yet.....
Gavin Lodewick
Experienced MS/Extra'er
Posts: 208
Joined: Thu Feb 02, 2006 1:47 pm
Location: South Africa

Re: Youtube videos, I need people to subscribe

Post by Gavin Lodewick »

panel wrote:Setting Lambda delay table in TS. How to make that work.
I hope soon :yeah!:

Gavin
whittlebeast
Super MS/Extra'er
Posts: 2221
Joined: Tue May 04, 2004 8:20 pm
Location: St Louis
Contact:

Re: Youtube videos, I need people to subscribe

Post by whittlebeast »

I did a video on Grounding.

https://youtu.be/EJ2TeodWDUE

Andy
Chanoquin
MS/Extra Newbie
Posts: 11
Joined: Mon Nov 26, 2018 10:03 am

Re: Youtube videos, I need people to subscribe

Post by Chanoquin »

Subscribed...
I am new to this forum, so I´ll try to catch up with the forum before I start watching Videos.
Thanks for taking your time to record....
AA
KW78
Helpful MS/Extra'er
Posts: 90
Joined: Wed Jul 13, 2011 12:53 pm

Re: Youtube videos, I need people to subscribe

Post by KW78 »

Subscribed!

Thanks for the content. I have used MS for a long time, been on this forum a long time, and just found your videos.

Learned something in all of them...

If you're taking requests, I would love a video series tutorial on power using MLV-hd. I didn't know you could right click on histogram and change the length of the tail before your video, for example. There are so many little things, but even some basics like how it appears MLV re-handles the 02 voltage vs the AFR readout, meaning if you tweaked your AFR calibration in TS it doesn't know that in MLV? I don't know. I am sure you know important minutia that isn't really minutia!

But also filters, calculated fields, and scatter plot formulas. When to use them, how to strategically use them. It seems so powerful of a tool and every time I use it, I feel it kicks my ass. There has to be a way to graphically represent almost any condition you are trying to tune, like wall wetting or PID control of closed loop fuel control. I am hoping my next car build I will be building track maps in MLV, per your suggestion from somewhere....

Anyway, thanks for all your efforts, I will try to support the "keep andy interested" fund as well!

Fellow road racer, tuner, car builder.
Kyle
Sector Purple Racing
Denver area.
whittlebeast
Super MS/Extra'er
Posts: 2221
Joined: Tue May 04, 2004 8:20 pm
Location: St Louis
Contact:

Re: Youtube videos, I need people to subscribe

Post by whittlebeast »

Thank you. Just over 3100 subscribers now.

Andy
Post Reply