How can I Enable the Diagnostic tool
Moderator: LT401Vette
-
- Master MS/Extra'er
- Posts: 612
- Joined: Fri Feb 25, 2011 4:28 pm
How can I Enable the Diagnostic tool
Hi phil, I am having problems with the diagnostic tab. I am using an experimental code 3.1.1V14(mariob) and I notice that since I flash the ecu and use the adequate inin file, The tab of the diagnostic tool is gray out and I can not us it. I really like the experimental code that I am using It is posible to enable it so i dont lose this feature in my registered version of TS?
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: How can I Enable the Diagnostic tool
The enable status of that is based on the signature as the function is tightly coupled to the firmware capability. If your code is based on ms2 extra it would work, but the signature needs to represent it as some form of ms2 extra.
The association is compiled in, you can not edit a file.
Where is this code and ini?
The association is compiled in, you can not edit a file.
Where is this code and ini?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Master MS/Extra'er
- Posts: 612
- Joined: Fri Feb 25, 2011 4:28 pm
Re: How can I Enable the Diagnostic tool
it is in the ms2 development forum I will post heres is the inin file
-
- Master MS/Extra'er
- Posts: 612
- Joined: Fri Feb 25, 2011 4:28 pm
Re: How can I Enable the Diagnostic tool
The code aparently it to big for attach in this forum here is the adress where you can download the zip V14
http://www.msextra.com/forums/viewtopic ... &start=260
http://www.msextra.com/forums/viewtopic ... &start=260
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: How can I Enable the Diagnostic tool
The serial Signature is:
MS2Extra 311 mb_v12
It needs to start with these to be identified as MS2e 3.x in TS 1.004:
MS2Extra Rel 3
MS2Extra Serial
MS2Extra serial
For future I can add the pattern "MS2Extra 3" in the next beta to support as it is..
MS2Extra 311 mb_v12
It needs to start with these to be identified as MS2e 3.x in TS 1.004:
MS2Extra Rel 3
MS2Extra Serial
MS2Extra serial
For future I can add the pattern "MS2Extra 3" in the next beta to support as it is..
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Master MS/Extra'er
- Posts: 612
- Joined: Fri Feb 25, 2011 4:28 pm
Re: How can I Enable the Diagnostic tool
I am sorry I could not follow what exactly i have to do. I did not wrote the code i am using it from the forum so my technical codings skills are non existent.
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: How can I Enable the Diagnostic tool
Unfortunately there is nothing you can do. Either who ever owns the code needs to change the signature, or you have to wait for a beta TS that recognizes the new signature.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Master MS/Extra'er
- Posts: 612
- Joined: Fri Feb 25, 2011 4:28 pm
Re: How can I Enable the Diagnostic tool
Thanks a lot I will let him know, Of course if the beta edition is available I am more than happy to give it a try thanks a lot.
Juan
Juan
-
- Master MS/Extra'er
- Posts: 612
- Joined: Fri Feb 25, 2011 4:28 pm
Re: How can I Enable the Diagnostic tool
sorry to bring this back. I think ts beta 19 is not recognizing 3.2.1 gslender v5 again.
Is the solution the same as before?
Juan
Is the solution the same as before?
Juan
Re: How can I Enable the Diagnostic tool
Why don't you only use MS2E? that will enable them to do whatever character after that.LT401Vette wrote:For future I can add the pattern "MS2Extra 3" in the next beta to support as it is..
Just suggesting.
(4G63T - MSIIextra) (4G13 - MS3-beta testing)
-
- Site Admin
- Posts: 39617
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: How can I Enable the Diagnostic tool
Or require newer firmwares to configure/enable the loggers through the ini file.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: How can I Enable the Diagnostic tool
It has not changed. Is there a new version of this with a new signature?I think ts beta 19 is not recognizing 3.2.1 gslender v5 again.
The available loggers has been steady for a while, but did change with versions. Currently all it needs is to start with:Why don't you only use MS2E?
"MS2Extra 3" and it is good... That seems easy enough and TS knows it is version 3 or better.
James' suggestion is really the the right one, but there haven't been too many other firmwares other than this one to drive the need. Compiling the signature match in also helps prevent theft of the firmware where people recompile the firmware with their own signature and call it their own.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html