1.04 to 1.19 question

For discussion of Phil Tobin's Tuner Studio software (Only about the tuning software itself, not about how to tune or firmware features)

Moderator: LT401Vette

Post Reply
turbo conversion
Super MS/Extra'er
Posts: 1281
Joined: Thu Aug 19, 2010 6:22 pm
Location: White House, TN USA

1.04 to 1.19 question

Post by turbo conversion »

I would like to try 1.19. Current: MS2 Extra 3.1.1 TS 1.04. I went to your site and downloaded the 1.19 and it created another TS with icon. Do I load my current tune then power off and then bring the controller on line. Thanks, David
1976 Datsun 280Z L28ET Garrett GT35R T3-T04E stage3 50 trim 63 A/R housing custom grind cam 2000-6000 rpm 440cc injectors intercooled 18 lbs. boost
3" exhaust turbo back LC-1 o2 sensor Hallman manual boost controller EDIS 6 ignition batch fire 60mm throttle body 5 spd T5 borg warner 3.54 lsd
kjones6039
Super MS/Extra'er
Posts: 1986
Joined: Sat Jul 22, 2006 8:02 pm
Location: Eureka, NV USA
Contact:

Re: 1.04 to 1.19 question

Post by kjones6039 »

turbo conversion wrote:I would like to try 1.19. Current: MS2 Extra 3.1.1 TS 1.04. I went to your site and downloaded the 1.19 and it created another TS with icon. Do I load my current tune then power off and then bring the controller on line. Thanks, David
That will work, but I would create a new project in 1.19 and load my current tune to that project. That way your tune will also be saved if you want to go back to 1.04......

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
turbo conversion
Super MS/Extra'er
Posts: 1281
Joined: Thu Aug 19, 2010 6:22 pm
Location: White House, TN USA

Re: 1.04 to 1.19 question

Post by turbo conversion »

Thank you Ken, that is what I will do. Also, how do you get my post to apear in your response? David
1976 Datsun 280Z L28ET Garrett GT35R T3-T04E stage3 50 trim 63 A/R housing custom grind cam 2000-6000 rpm 440cc injectors intercooled 18 lbs. boost
3" exhaust turbo back LC-1 o2 sensor Hallman manual boost controller EDIS 6 ignition batch fire 60mm throttle body 5 spd T5 borg warner 3.54 lsd
kjones6039
Super MS/Extra'er
Posts: 1986
Joined: Sat Jul 22, 2006 8:02 pm
Location: Eureka, NV USA
Contact:

Re: 1.04 to 1.19 question

Post by kjones6039 »

turbo conversion wrote:Thank you Ken, that is what I will do. Also, how do you get my post to apear in your response? David
By clicking the "QUOTE" button at the top right of your post.

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
Post Reply