Ign signal, tps, nightmare. Base map would be great!

Tuning concepts, methods, tips etc.

Moderators: jsmcortina, muythaibxr

black 89turbo
Experienced MS/Extra'er
Posts: 161
Joined: Tue Sep 06, 2011 2:33 pm

Re: Ign signal, tps, nightmare. Base map would be great!

Post by black 89turbo »

yes
Peter Florance
Super MS/Extra'er
Posts: 3653
Joined: Fri Apr 02, 2004 8:40 pm
Location: Virginia Beach, VA
Contact:

Re: Ign signal, tps, nightmare. Base map would be great!

Post by Peter Florance »

black 89turbo wrote:yes
PM me your email and I'll send you a starter fuel table
Peter Florance
PF Tuning
81 BMW Euro 528i ESP Car
60-2 Wheel LS2 Coils, Low Z Inj
Co-Driver 1999 BMW E46 DSP car.
billr
Super MS/Extra'er
Posts: 6828
Joined: Sun May 15, 2011 11:41 am
Location: Walnut Creek, Calif. USA

Re: Ign signal, tps, nightmare. Base map would be great!

Post by billr »

Referring to "Tune1.msq" posted 5/3/2012:

To the right of "BANK 1 Dead time @13.2V(ms)" I see a data-box with ".752" in it.
black 89turbo
Experienced MS/Extra'er
Posts: 161
Joined: Tue Sep 06, 2011 2:33 pm

Re: Ign signal, tps, nightmare. Base map would be great!

Post by black 89turbo »

billr wrote:Referring to "Tune1.msq" posted 5/3/2012:

To the right of "BANK 1 Dead time @13.2V(ms)" I see a data-box with ".752" in it.
Screen shot?
It deffinetly was set @ 7.0
Need to make sure were all on the same page and looking at the same thing.
black 89turbo
Experienced MS/Extra'er
Posts: 161
Joined: Tue Sep 06, 2011 2:33 pm

Re: Ign signal, tps, nightmare. Base map would be great!

Post by black 89turbo »

.
Peter Florance
Super MS/Extra'er
Posts: 3653
Joined: Fri Apr 02, 2004 8:40 pm
Location: Virginia Beach, VA
Contact:

Re: Ign signal, tps, nightmare. Base map would be great!

Post by Peter Florance »

black 89turbo wrote:.
Sounds like your req fuel is way too small or the problems in VE table made you have to run such a large value

Try .8 and the ve table I sent you.
Peter Florance
PF Tuning
81 BMW Euro 528i ESP Car
60-2 Wheel LS2 Coils, Low Z Inj
Co-Driver 1999 BMW E46 DSP car.
billr
Super MS/Extra'er
Posts: 6828
Joined: Sun May 15, 2011 11:41 am
Location: Walnut Creek, Calif. USA

Re: Ign signal, tps, nightmare. Base map would be great!

Post by billr »

Here it is, also the .msq Maybe it's a difference in the TS I'm using?
Tune1.msq
Tune1.JPG
black 89turbo
Experienced MS/Extra'er
Posts: 161
Joined: Tue Sep 06, 2011 2:33 pm

Re: Ign signal, tps, nightmare. Base map would be great!

Post by black 89turbo »

No go. I uploaded the table peter sent, set the dead time to .8. I also tried to up the PWM current all the way to 60 and still nothing. Take the dead time and put 7.0 in fires up without a hesitation. :?
Peter Florance
Super MS/Extra'er
Posts: 3653
Joined: Fri Apr 02, 2004 8:40 pm
Location: Virginia Beach, VA
Contact:

Re: Ign signal, tps, nightmare. Base map would be great!

Post by Peter Florance »

black 89turbo wrote:No go. I uploaded the table peter sent, set the dead time to .8. I also tried to up the PWM current all the way to 60 and still nothing. Take the dead time and put 7.0 in fires up without a hesitation. :?
which outputs are you using? MS3X or standard?
Peter Florance
PF Tuning
81 BMW Euro 528i ESP Car
60-2 Wheel LS2 Coils, Low Z Inj
Co-Driver 1999 BMW E46 DSP car.
black 89turbo
Experienced MS/Extra'er
Posts: 161
Joined: Tue Sep 06, 2011 2:33 pm

Re: Ign signal, tps, nightmare. Base map would be great!

Post by black 89turbo »

billr wrote:Here it is, also the .msq Maybe it's a difference in the TS I'm using?
Weird, very weird.
black 89turbo
Experienced MS/Extra'er
Posts: 161
Joined: Tue Sep 06, 2011 2:33 pm

Re: Ign signal, tps, nightmare. Base map would be great!

Post by black 89turbo »

Peter Florance wrote:
black 89turbo wrote:No go. I uploaded the table peter sent, set the dead time to .8. I also tried to up the PWM current all the way to 60 and still nothing. Take the dead time and put 7.0 in fires up without a hesitation. :?
which outputs are you using? MS3X or standard?
Standard/main board. Not getting into the ms3x portion yet. lol rookie at ms :oops:
Peter Florance
Super MS/Extra'er
Posts: 3653
Joined: Fri Apr 02, 2004 8:40 pm
Location: Virginia Beach, VA
Contact:

Re: Ign signal, tps, nightmare. Base map would be great!

Post by Peter Florance »

black 89turbo wrote:
Peter Florance wrote:
black 89turbo wrote:No go. I uploaded the table peter sent, set the dead time to .8. I also tried to up the PWM current all the way to 60 and still nothing. Take the dead time and put 7.0 in fires up without a hesitation. :?
which outputs are you using? MS3X or standard?
Standard/main board. Not getting into the ms3x portion yet. lol rookie at ms :oops:
edit: I wonder if these are really high z injectors or there are ballast resistors installed.
Peter Florance
PF Tuning
81 BMW Euro 528i ESP Car
60-2 Wheel LS2 Coils, Low Z Inj
Co-Driver 1999 BMW E46 DSP car.
black 89turbo
Experienced MS/Extra'er
Posts: 161
Joined: Tue Sep 06, 2011 2:33 pm

Re: Ign signal, tps, nightmare. Base map would be great!

Post by black 89turbo »

1g DSM 450cc Blue tops #B450l

Non-Turbo 1.8L - N210H Injectors-casting #INP-057 (210cc High Impedance)
Non-Turbo 4G63 - N240H Injectors-casting #INP-059 (240cc High Impedance)
Turbo 4G63 A/T - B390L Injectors-casting #INP-008 (390cc Low Impedance)
Turbo 4G63 M/T - B450L Injectors-casting #INP-009 (450cc Low Impedance)
2G Turbo BlackTops -MDL450 casting #IPN-081 (450cc Low Impedance)
2.4 - MDH275-casting #IPN-065 (275cc High Impedance)
JDM motors that came with the B16G had yellow 510cc injectors
billr
Super MS/Extra'er
Posts: 6828
Joined: Sun May 15, 2011 11:41 am
Location: Walnut Creek, Calif. USA

Re: Ign signal, tps, nightmare. Base map would be great!

Post by billr »

Make it simple for me, forget about the injectors P/Ns and top colors; how many ohms of resistance on one?
black 89turbo
Experienced MS/Extra'er
Posts: 161
Joined: Tue Sep 06, 2011 2:33 pm

Re: Ign signal, tps, nightmare. Base map would be great!

Post by black 89turbo »

billr wrote:Make it simple for me, forget about the injectors P/Ns and top colors; how many ohms of resistance on one?
They ALL have 2.8ish give or take .1. I ohm them all out.
Peter Florance
Super MS/Extra'er
Posts: 3653
Joined: Fri Apr 02, 2004 8:40 pm
Location: Virginia Beach, VA
Contact:

Re: Ign signal, tps, nightmare. Base map would be great!

Post by Peter Florance »

black 89turbo wrote:
billr wrote:Make it simple for me, forget about the injectors P/Ns and top colors; how many ohms of resistance on one?
They ALL have 2.8ish give or take .1. I ohm them all out.
My 4G63 has ballast resistors
Peter Florance
PF Tuning
81 BMW Euro 528i ESP Car
60-2 Wheel LS2 Coils, Low Z Inj
Co-Driver 1999 BMW E46 DSP car.
black 89turbo
Experienced MS/Extra'er
Posts: 161
Joined: Tue Sep 06, 2011 2:33 pm

Re: Ign signal, tps, nightmare. Base map would be great!

Post by black 89turbo »

Peter Florance wrote:
black 89turbo wrote:
billr wrote:Make it simple for me, forget about the injectors P/Ns and top colors; how many ohms of resistance on one?
They ALL have 2.8ish give or take .1. I ohm them all out.
My 4G63 has ballast resistors
Oem haress, ecu & resistor box?
Peter Florance
Super MS/Extra'er
Posts: 3653
Joined: Fri Apr 02, 2004 8:40 pm
Location: Virginia Beach, VA
Contact:

Re: Ign signal, tps, nightmare. Base map would be great!

Post by Peter Florance »

black 89turbo wrote:
Oem haress, ecu & resistor box?
OEM harness, resistors and MS
Peter Florance
PF Tuning
81 BMW Euro 528i ESP Car
60-2 Wheel LS2 Coils, Low Z Inj
Co-Driver 1999 BMW E46 DSP car.
black 89turbo
Experienced MS/Extra'er
Posts: 161
Joined: Tue Sep 06, 2011 2:33 pm

Re: Ign signal, tps, nightmare. Base map would be great!

Post by black 89turbo »

Peter Florance wrote:
black 89turbo wrote:
Oem haress, ecu & resistor box?
OEM harness, resistors and MS
Hmm, maybe put a resistor box in? I never used a resistor box using these injectors on AEM, Microwreck or helltech all 4 cars ran for year/years before either upgradding injectors ect. You have the same injectors correct? Your running MS2? Do you have a wiring diagram of the resistor pack put into play?
Peter Florance
Super MS/Extra'er
Posts: 3653
Joined: Fri Apr 02, 2004 8:40 pm
Location: Virginia Beach, VA
Contact:

Re: Ign signal, tps, nightmare. Base map would be great!

Post by Peter Florance »

black 89turbo wrote:
Peter Florance wrote:
black 89turbo wrote:
Oem haress, ecu & resistor box?
OEM harness, resistors and MS
Hmm, maybe put a resistor box in? I never used a resistor box using these injectors on AEM, Microwreck or helltech all 4 cars ran for year/years before either upgradding injectors ect. You have the same injectors correct? Your running MS2? Do you have a wiring diagram of the resistor pack put into play?
No you don't need one; my question is whether the ballast resistors are still in your harness.

My old tech left this MS1 car behind after he hurt the motor tuning it and moved back to Ohio. Signed it over to me when the city was going to tow it.

Just got pistons put in it so don't know much more about it.

Eagle Talon which has ballast resistors and low z injectors
Peter Florance
PF Tuning
81 BMW Euro 528i ESP Car
60-2 Wheel LS2 Coils, Low Z Inj
Co-Driver 1999 BMW E46 DSP car.
Post Reply