Changing Bar Gauges increase direction

For discussion of Phil Tobin's Tuner Studio software (Only about the tuning software itself, not about how to tune or firmware features)

Moderator: LT401Vette

Changing Bar Gauges increase direction

Postby wrenchdad » Wed May 09, 2012 11:20 pm

Guys,

Is there a way to make the bar gauges go from right to left instead of the normal left to right on increasing input?

Also while on the subject of bar gauges is there a way to make one have a ZERO at the center of the bar? Say to use it for O2 correction so that centered its ZERO correction.

thanks wd
wrenchdad
Master MS/Extra'er
 
Posts: 597
Joined: Mon Feb 14, 2005 5:30 am
Location: Natchez, Mississippi

Re: Changing Bar Gauges increase direction

Postby LT401Vette » Thu May 10, 2012 6:05 am

I _thought_ you just had to select "Counter Clockwise Rotation" in the Properties Menu.
But I just tried it and it appears I have not yet put support in the bar graph for reverse motion.

So I guess you can't.. I'll have to add that.

There is no center based bar, but if the above worked, you could make one pretty easy using 2 bar graphs.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
User avatar
LT401Vette
Super MS/Extra'er
 
Posts: 8133
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC

Re: Changing Bar Gauges increase direction

Postby wrenchdad » Thu May 10, 2012 3:00 pm

LT401Vette wrote:I _thought_ you just had to select "Counter Clockwise Rotation" in the Properties Menu.



Yep, That's what I tried but didn't change the direction.

thanks, wd
wrenchdad
Master MS/Extra'er
 
Posts: 597
Joined: Mon Feb 14, 2005 5:30 am
Location: Natchez, Mississippi

Re: Changing Bar Gauges increase direction

Postby LT401Vette » Thu May 10, 2012 3:17 pm

I did activate it today.

While doing so I nodiced the dashed bars are already honoring the reversed rotation.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
User avatar
LT401Vette
Super MS/Extra'er
 
Posts: 8133
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC

Re: Changing Bar Gauges increase direction

Postby wrenchdad » Thu May 10, 2012 3:28 pm

COOL !!! thanks :yeah!:

wd
wrenchdad
Master MS/Extra'er
 
Posts: 597
Joined: Mon Feb 14, 2005 5:30 am
Location: Natchez, Mississippi

Re: Changing Bar Gauges increase direction

Postby wrenchdad » Thu May 10, 2012 3:33 pm

OH, I forgot to ask is that in the release version or beta OR both?

thanks again, wd
wrenchdad
Master MS/Extra'er
 
Posts: 597
Joined: Mon Feb 14, 2005 5:30 am
Location: Natchez, Mississippi

Re: Changing Bar Gauges increase direction

Postby LT401Vette » Fri May 11, 2012 5:24 am

I'm working with the beta, I don't think the Dashed bar renderer has changed since 1.004, but would have to try it.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
User avatar
LT401Vette
Super MS/Extra'er
 
Posts: 8133
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC


Return to Tuner Studio

Who is online

Users browsing this forum: No registered users and 1 guest