Changing Bar Gauges increase direction

For discussion of Phil Tobin's Tuner Studio software (Only about the tuning software itself, not about how to tune or firmware features)

Moderator: LT401Vette

Post Reply
wrenchdad
Master MS/Extra'er
Posts: 614
Joined: Mon Feb 14, 2005 5:30 am
Location: Natchez, Mississippi

Changing Bar Gauges increase direction

Post by wrenchdad »

Guys,

Is there a way to make the bar gauges go from right to left instead of the normal left to right on increasing input?

Also while on the subject of bar gauges is there a way to make one have a ZERO at the center of the bar? Say to use it for O2 correction so that centered its ZERO correction.

thanks wd
LT401Vette
Super MS/Extra'er
Posts: 12697
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC
Contact:

Re: Changing Bar Gauges increase direction

Post by LT401Vette »

I _thought_ you just had to select "Counter Clockwise Rotation" in the Properties Menu.
But I just tried it and it appears I have not yet put support in the bar graph for reverse motion.

So I guess you can't.. I'll have to add that.

There is no center based bar, but if the above worked, you could make one pretty easy using 2 bar graphs.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
wrenchdad
Master MS/Extra'er
Posts: 614
Joined: Mon Feb 14, 2005 5:30 am
Location: Natchez, Mississippi

Re: Changing Bar Gauges increase direction

Post by wrenchdad »

LT401Vette wrote:I _thought_ you just had to select "Counter Clockwise Rotation" in the Properties Menu.
Yep, That's what I tried but didn't change the direction.

thanks, wd
LT401Vette
Super MS/Extra'er
Posts: 12697
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC
Contact:

Re: Changing Bar Gauges increase direction

Post by LT401Vette »

I did activate it today.

While doing so I nodiced the dashed bars are already honoring the reversed rotation.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
wrenchdad
Master MS/Extra'er
Posts: 614
Joined: Mon Feb 14, 2005 5:30 am
Location: Natchez, Mississippi

Re: Changing Bar Gauges increase direction

Post by wrenchdad »

COOL !!! thanks :yeah!:

wd
wrenchdad
Master MS/Extra'er
Posts: 614
Joined: Mon Feb 14, 2005 5:30 am
Location: Natchez, Mississippi

Re: Changing Bar Gauges increase direction

Post by wrenchdad »

OH, I forgot to ask is that in the release version or beta OR both?

thanks again, wd
LT401Vette
Super MS/Extra'er
Posts: 12697
Joined: Sat Jul 16, 2005 8:07 am
Location: Moorseville, NC
Contact:

Re: Changing Bar Gauges increase direction

Post by LT401Vette »

I'm working with the beta, I don't think the Dashed bar renderer has changed since 1.004, but would have to try it.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Post Reply