MS3 beta 1.0.6 released

General support questions and announcements for MS3. See also MS3 manuals.

Moderators: jsmcortina, muythaibxr

Post Reply
jsmcortina
Site Admin
Posts: 39585
Joined: Mon May 03, 2004 1:34 am
Location: Birmingham, UK
Contact:

MS3 beta 1.0.6 released

Post by jsmcortina »

This is a bugfix release on 1.0.5. Assuming it tests ok, the aim is to promote it to "release" quite quickly.

Changes:
Fix injector trim pulsewidth overflow also allows larger pulsewidths
SDcard VBR support

The pulsewidth issue was only apparent with very large (> 43ms) pulsewidths during or just after cranking and only if injector trim was enabled.
The SDcard changes bring back a few tweaks from the pre-1.1 development code.

The zip can be downloaded from http://www.msextra.com/doc/ms3/files/be ... -1.0.6.zip

The new firmware loaders are included as standard.

James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk

My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
MG four six eight
Helpful MS/Extra'er
Posts: 43
Joined: Sun May 17, 2009 10:36 pm

Re: MS3 beta 1.0.6 released

Post by MG four six eight »

Just reporting back that 1.0.6 is working well! Seq cranking pulse width readings are normal and the engine starts right up, compared to 2.6 ms (during no start) when the bug would show up. Thanks James :)

Bill
frank_ster
Experienced MS/Extra'er
Posts: 226
Joined: Tue Sep 11, 2007 11:07 am

Re: MS3 beta 1.0.6 released

Post by frank_ster »

i appear to be having an issue,

i changed over to this version a few days ago.

only issue i have is with the pid controled ego correction.
my target afr is 14.0-1 at idle 14.7 everywhere in cruse under 100 kpa and then drops down to 11-1 in 200kpa.

when ideling it seams the target is 13-1 and in cruse its 14-1. it stays at these numbers regardlss of pid settings. even with proportinal to 100 intergral at 0 and deritive at 0 it still follows the same.

as soon as i set to simple ego it works as it should it adjusts to my target afr's.
so i have a work around just reporting my issue.

i can post 2 data logs and my msq upon request
2005 subaru legacy with buick grandnational engine and awd :D
1976 gmc k10 pickup vortec 383 tbi ms2 nv4500 3.42 final drives
jsmcortina
Site Admin
Posts: 39585
Joined: Mon May 03, 2004 1:34 am
Location: Birmingham, UK
Contact:

Re: MS3 beta 1.0.6 released

Post by jsmcortina »

Nothing was changed relating to EGO control.

James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk

My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
frank_ster
Experienced MS/Extra'er
Posts: 226
Joined: Tue Sep 11, 2007 11:07 am

Re: MS3 beta 1.0.6 released

Post by frank_ster »

Ok but why is the pid control ego not working ? i did not try 1.0.5 maybe something in that or previous version that was changed ?
2005 subaru legacy with buick grandnational engine and awd :D
1976 gmc k10 pickup vortec 383 tbi ms2 nv4500 3.42 final drives
teg
Experienced MS/Extra'er
Posts: 291
Joined: Sun Sep 05, 2004 2:02 pm
Location: Finland

Re: MS3 beta 1.0.6 released

Post by teg »

I don't think PID has anything to do with targets?
Opel Kadett C City 2.0 16V Turbo
adamnreeves
Experienced MS/Extra'er
Posts: 220
Joined: Fri Nov 20, 2009 10:55 am

Re: MS3 beta 1.0.6 released

Post by adamnreeves »

jsmcortina wrote:This is a bugfix release on 1.0.5. Assuming it tests ok, the aim is to promote it to "release" quite quickly.

James
How quickly we talking? Been holding off installing 1.0.6 waiting for the release.
Westfield SEiGHT 4.6 Stage III
Running Megasquirt3 Wasted Spark using EDIS-8 Firmware MS3Extra 1.1.1
Build site
jsmcortina
Site Admin
Posts: 39585
Joined: Mon May 03, 2004 1:34 am
Location: Birmingham, UK
Contact:

Re: MS3 beta 1.0.6 released

Post by jsmcortina »

Why?
The code won't change aside from the word that appears in the title bar.

James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk

My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
adamnreeves
Experienced MS/Extra'er
Posts: 220
Joined: Fri Nov 20, 2009 10:55 am

Re: MS3 beta 1.0.6 released

Post by adamnreeves »

So just a tag then. I'll update over the weekend. Cheers.
Westfield SEiGHT 4.6 Stage III
Running Megasquirt3 Wasted Spark using EDIS-8 Firmware MS3Extra 1.1.1
Build site
adamnreeves
Experienced MS/Extra'er
Posts: 220
Joined: Fri Nov 20, 2009 10:55 am

Re: MS3 beta 1.0.6 released

Post by adamnreeves »

I've upgraded and started her up in the garage.
Westfield SEiGHT 4.6 Stage III
Running Megasquirt3 Wasted Spark using EDIS-8 Firmware MS3Extra 1.1.1
Build site
Post Reply