HELP! Composite logger, Toth Logger, etc DON'T WORK.
Moderator: LT401Vette
-
- MS/Extra Newbie
- Posts: 21
- Joined: Tue Dec 27, 2016 4:50 am
HELP! Composite logger, Toth Logger, etc DON'T WORK.
I get this:
"Empty read, No Data Received from Controller"
MSII V3.0 with a new msextra firmware. The rest works perfectly, I can get signal from MAP, TPS, thermistors (RPM on the way)...
It's really hard to sync RPM without that, I know I could do that manually with an oscilloscope but mine is quite slow using both channels.
Which can be the problem? Firmware? computer? cable? ms2 daughterboard?
Thanks!
"Empty read, No Data Received from Controller"
MSII V3.0 with a new msextra firmware. The rest works perfectly, I can get signal from MAP, TPS, thermistors (RPM on the way)...
It's really hard to sync RPM without that, I know I could do that manually with an oscilloscope but mine is quite slow using both channels.
Which can be the problem? Firmware? computer? cable? ms2 daughterboard?
Thanks!
-
- Super MS/Extra'er
- Posts: 4122
- Joined: Fri May 07, 2004 3:33 am
- Location: Australia
Re: HELP! Composite logger, Toth Logger, etc DON'T WORK.
Are you following the steps shown in the manual? http://www.msextra.com/doc/pdf/html/Meg ... 5-337.html
Find the Manuals up top under Quick links: Manuals.
Cheers Luke
Cheers Luke
-
- Super MS/Extra'er
- Posts: 12731
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: HELP! Composite logger, Toth Logger, etc DON'T WORK.
If it is getting empty reads, the MS may not be seeing any signal for the crank. Pots?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- MS/Extra Newbie
- Posts: 21
- Joined: Tue Dec 27, 2016 4:50 am
Re: HELP! Composite logger, Toth Logger, etc DON'T WORK.
Thanks, I solved this when I finally synchronized RPM
-
- Super MS/Extra'er
- Posts: 2221
- Joined: Tue May 04, 2004 8:20 pm
- Location: St Louis
- Contact:
Re: HELP! Composite logger, Toth Logger, etc DON'T WORK.
I was seeing that when I was chasing sync issues. Sometimes I would get nothing.
I still can't seen to get a MAP log. The pages never start piling up.
ANdy
I still can't seen to get a MAP log. The pages never start piling up.
ANdy
-
- MS/Extra Newbie
- Posts: 21
- Joined: Tue Dec 27, 2016 4:50 am
Re: HELP! Composite logger, Toth Logger, etc DON'T WORK.
In the composite I only get RPM, CAM and sync loss. No TPS, no MAP, no O2...whittlebeast wrote:I was seeing that when I was chasing sync issues. Sometimes I would get nothing.
I still can't seen to get a MAP log. The pages never start piling up.
ANdy
idk
-
- Super MS/Extra'er
- Posts: 2221
- Joined: Tue May 04, 2004 8:20 pm
- Location: St Louis
- Contact:
Re: HELP! Composite logger, Toth Logger, etc DON'T WORK.
A Composite log is a little funny to read. Post yours here.
Here is one off my car.
http://www.nbs-stl.com/CrxTypeR/40%20to ... %20log.csv
Andy
Here is one off my car.
http://www.nbs-stl.com/CrxTypeR/40%20to ... %20log.csv
Andy
-
- Site Admin
- Posts: 39613
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: HELP! Composite logger, Toth Logger, etc DON'T WORK.
That's correct.EnricGuardiaSinfreu wrote:In the composite I only get RPM, CAM and sync loss. No TPS, no MAP, no O2...
If you want a normal datalog, then go to Datalogging -> Start Datalogging
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".