Possible bug
Moderator: LT401Vette
Possible bug
While making change to a table, I had a section highlighted where I was subtracting from the highlighted area in the table. I noticed the numbers started changing seemingly all by it self! I have seen this behavior before in TunerStudio, also in previous versions but it seemed too random! I could not get it to repeat. Until now! What I found is that if you highlight an area and have you finger on the scroll bar you are in for a big surprise! The numbers will go up or down with the movement on the scroll bar.
-
- Experienced MS/Extra'er
- Posts: 372
- Joined: Sat Dec 31, 2011 6:10 am
- Location: Netherlands
- Contact:
Re: Possible bug
I have also occassionaly seen a cell's value change a second time, after say, selecting a row or area of cells, and interpolate the values.
Although I can't produce scrollbars in a table though. The table is just resized to whatever the window size is.
Even if the window is resized way narrow, the rest of the table is just not shown anymore. But no scrollbars.
Although I can't produce scrollbars in a table though. The table is just resized to whatever the window size is.
Even if the window is resized way narrow, the rest of the table is just not shown anymore. But no scrollbars.
Daily driver: 1973 Dodge Dart - 360ci engine - 11.3:1cr - MS3x - ignition only. 42RH/A500 OD+LU transmission / 3.23 gears
--------------
Website: https://www.bigblockmopar.nl/
YouTube Channel: https://www.youtube.com/c/BigBlockMopar
--------------
Website: https://www.bigblockmopar.nl/
YouTube Channel: https://www.youtube.com/c/BigBlockMopar
-
- Site Admin
- Posts: 39618
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: Possible bug
The scroll wheel on the mouse changes the selected values.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Possible bug
Yes, as James said; the scroll button raises and lowers the selected cells. This was a requested here on the forum a little while back..samh wrote:While making change to a table, I had a section highlighted where I was subtracting from the highlighted area in the table. I noticed the numbers started changing seemingly all by it self! I have seen this behavior before in TunerStudio, also in previous versions but it seemed too random! I could not get it to repeat. Until now! What I found is that if you highlight an area and have you finger on the scroll bar you are in for a big surprise! The numbers will go up or down with the movement on the scroll bar.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Possible bug
What you may likely be seeing is: TS will interpolate to the true interpolated value, but on some tables the underlying ECU value does not match that value directly, so it is then brought to the closest supported value.BigBlockMopar wrote:I have also occassionaly seen a cell's value change a second time, after say, selecting a row or area of cells, and interpolate the values.
Although I can't produce scrollbars in a table though. The table is just resized to whatever the window size is.
Even if the window is resized way narrow, the rest of the table is just not shown anymore. But no scrollbars.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Experienced MS/Extra'er
- Posts: 372
- Joined: Sat Dec 31, 2011 6:10 am
- Location: Netherlands
- Contact:
Re: Possible bug
Sounds like that's what I have seen happen.
Since it are only tiny decimal 'changes' I sometimes see, I wasn't too worried about it.
Since it are only tiny decimal 'changes' I sometimes see, I wasn't too worried about it.
Daily driver: 1973 Dodge Dart - 360ci engine - 11.3:1cr - MS3x - ignition only. 42RH/A500 OD+LU transmission / 3.23 gears
--------------
Website: https://www.bigblockmopar.nl/
YouTube Channel: https://www.youtube.com/c/BigBlockMopar
--------------
Website: https://www.bigblockmopar.nl/
YouTube Channel: https://www.youtube.com/c/BigBlockMopar
Re: Possible bug
If you are tuning by yourself or have some driving on the highway this is a big problem! bumpy road or making changes during a shift etc... = major changes! and if you don't catch it your table is screwed! Also can lead to a stall. I know it has happened! So I am asking please remove or modify so it does not happen when not wanted! I know there are buttons that can be programed to increase or decrease the selected cell the desired amount , and that works fine! I have a lot of roads to use for tuning drivability with little to no traffic. I know most don't bother to tune for drivability I do it often and like it! But now I know what is going on! That feature I feel is totally unsafe for most of my situations.
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Possible bug
I'm sure a setting can be added to disable this for those that don't want it.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Re: Possible bug
Cool please let us know when these changes will take effect. I will be eagerly awaiting them!
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Possible bug
This is implemented for the next beta.
You can turn it off via the main menu:
Options --> Preferences --> Mouse wheel scroll changes selected Table cells
You can turn it off via the main menu:
Options --> Preferences --> Mouse wheel scroll changes selected Table cells
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html