dwell stuck at .8 and spikes up to 84.7

All questions about MS2/Microsquirt/Microsquirt module. See also MS2/Extra manuals

Moderators: jsmcortina, muythaibxr

mini-dunger
MS/Extra Newbie
Posts: 20
Joined: Tue Jul 04, 2017 2:39 am

dwell stuck at .8 and spikes up to 84.7

Post by mini-dunger »

hello all

I have a misfire and a stumblbue at idle. I have been working on my fuel table but i have come to realise its an ignition problem.

I have an edis4 coil and module.
from what i understand its non adjustable in a programming sense. I have heard it may be
a capacitor in the megasquirt?

I have a clear RPM signal
I have done a tooth log and its clear and fine

any ideas fellas ?
mini-dunger
MS/Extra Newbie
Posts: 20
Joined: Tue Jul 04, 2017 2:39 am

Re: dwell stuck at .8 and spikes up to 84.7

Post by mini-dunger »

have included a log :}
Attachments
2017-12-16_21.32.51.msl
(195.6 KiB) Downloaded 25 times
kjones6039
Super MS/Extra'er
Posts: 1986
Joined: Sat Jul 22, 2006 8:02 pm
Location: Eureka, NV USA
Contact:

Re: dwell stuck at .8 and spikes up to 84.7

Post by kjones6039 »

Can you post the MSQ that goes with that log?

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
mini-dunger
MS/Extra Newbie
Posts: 20
Joined: Tue Jul 04, 2017 2:39 am

Re: dwell stuck at .8 and spikes up to 84.7

Post by mini-dunger »

i have included the current tune.

its supercharged with a sc12 I have edis ignition and a vacuum operated air bypass valve from a late model mini.
Attachments
1040cc supercharged mini.msq
(119.44 KiB) Downloaded 24 times
kjones6039
Super MS/Extra'er
Posts: 1986
Joined: Sat Jul 22, 2006 8:02 pm
Location: Eureka, NV USA
Contact:

Re: dwell stuck at .8 and spikes up to 84.7

Post by kjones6039 »

The first thing that jumps out at me is.......

Dwell Type should be set to Fixed Duty (NOT Standard as you have it) when running EDIS!

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
mini-dunger
MS/Extra Newbie
Posts: 20
Joined: Tue Jul 04, 2017 2:39 am

Re: dwell stuck at .8 and spikes up to 84.7

Post by mini-dunger »

thanks for your reply mate. Have tried a few different settings. I have fixed the dwell in the log I have attached to this post.... still no improvement
Attachments
log with dwell set to fixed.msl
(88.03 KiB) Downloaded 22 times
mini-dunger
MS/Extra Newbie
Posts: 20
Joined: Tue Jul 04, 2017 2:39 am

Re: dwell stuck at .8 and spikes up to 84.7

Post by mini-dunger »

just to add. when I received my ecu the chipset had been dislodged and it was rattling around inside the unit.

I had messed around inside the box and re-fitted it. I think i even put it in back to front initially.

is there a part in the box that relates directly to the dwell settings?

cheers
jsmcortina
Site Admin
Posts: 39587
Joined: Mon May 03, 2004 1:34 am
Location: Birmingham, UK
Contact:

Re: dwell stuck at .8 and spikes up to 84.7

Post by jsmcortina »

mini-dunger wrote:is there a part in the box that relates directly to the dwell settings?
Dwell is irrelevant with EDIS. The module controls timing and dwell based on the signal sent from the ECU.

Use a strobe to make sure that the actual strobed timing matches what you are seeing shown in TunerStudio.

James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk

My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
mini-dunger
MS/Extra Newbie
Posts: 20
Joined: Tue Jul 04, 2017 2:39 am

Re: dwell stuck at .8 and spikes up to 84.7

Post by mini-dunger »

thanks for your reply

i have had the timing fixed the whole time as I have been tuning the fuel side.

the timing light is the same as what tuner studio is telling me.
rickb794
Super MS/Extra'er
Posts: 6155
Joined: Sun Dec 21, 2008 10:28 am
Location: Portland OR

Re: dwell stuck at .8 and spikes up to 84.7

Post by rickb794 »

You cant tune fuel if you have a flat timing table, the fueling requirements will change when you enable spark advance control.

Read the manual and follow the instructions to the letter for EDIS usage.

However, I would not use the EDIS module as it does not allow MS full control of the spark.
The EDIS trigger wheel and sensor in addition to the EDIS coil are great parts to use with MS.
MS support of EDIS is a legacy holdover from MS1 and a v2.2 main board that does not natively support ignition.
Correctly identify your MS ecu here
Read the Do's and Don'ts to avoid the common pitfalls before starting your install or asking for help
Use only these manuals other manuals may cause brain damage or worse.
kjones6039
Super MS/Extra'er
Posts: 1986
Joined: Sat Jul 22, 2006 8:02 pm
Location: Eureka, NV USA
Contact:

Re: dwell stuck at .8 and spikes up to 84.7

Post by kjones6039 »

rickb794 wrote:However, I would not use the EDIS module as it does not allow MS full control of the spark.
The EDIS trigger wheel and sensor in addition to the EDIS coil are great parts to use with MS.
MS support of EDIS is a legacy holdover from MS1 and a v2.2 main board that does not natively support ignition.
AMEN!!!

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
mini-dunger
MS/Extra Newbie
Posts: 20
Joined: Tue Jul 04, 2017 2:39 am

Re: dwell stuck at .8 and spikes up to 84.7

Post by mini-dunger »

thanks for your replys

I understand that the fueling requirements will change with a timing map based on the table.

I also understand the complexity of tuning. My timing advance will be all in by 3000rpm and limited to around 25 degrees. So fixing it at 25 and developing a base tune at this isnt as stupid an idea as it sounds.

regardless of the fixed timing and any other aspects of my tune the dwell is doing something entirely incorrect.
kjones6039
Super MS/Extra'er
Posts: 1986
Joined: Sat Jul 22, 2006 8:02 pm
Location: Eureka, NV USA
Contact:

Re: dwell stuck at .8 and spikes up to 84.7

Post by kjones6039 »

We all feel your frustration!

But, as James pointed out above,
Dwell is irrelevant with EDIS. The module controls timing and dwell based on the signal sent from the ECU.
Hence, Rick pointed out,
However, I would not use the EDIS module as it does not allow MS full control of the spark.
Then I jumped in and agreed with both of them!

There is simply no way (that I'm aware of) to measure (or control) the dwell that the EDIS module is applying!
That is one of several reasons why I abandoned EDIS, years ago. I wanted full control of the various ignition functions.

I will now get my big nose out of this thread and go back to my corner. :lol:

Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
jsmcortina
Site Admin
Posts: 39587
Joined: Mon May 03, 2004 1:34 am
Location: Birmingham, UK
Contact:

Re: dwell stuck at .8 and spikes up to 84.7

Post by jsmcortina »

EDIS can work fine, but as I said, the Megasquirt has no control over dwell and any "dwell" it reports is meaningless.

James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk

My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
turbo conversion
Super MS/Extra'er
Posts: 1281
Joined: Thu Aug 19, 2010 6:22 pm
Location: White House, TN USA

Re: dwell stuck at .8 and spikes up to 84.7

Post by turbo conversion »

I am using EDIS 6 with module and the engine runs awesome with all kind of crazy dwell numbers.

As James said, ignore the dwell numbers as they are irrelevant.

As rickb794 said, turn off fixed timing and build a timing map or you will have to retune everything.

David
1976 Datsun 280Z L28ET Garrett GT35R T3-T04E stage3 50 trim 63 A/R housing custom grind cam 2000-6000 rpm 440cc injectors intercooled 18 lbs. boost
3" exhaust turbo back LC-1 o2 sensor Hallman manual boost controller EDIS 6 ignition batch fire 60mm throttle body 5 spd T5 borg warner 3.54 lsd
mini-dunger
MS/Extra Newbie
Posts: 20
Joined: Tue Jul 04, 2017 2:39 am

Re: dwell stuck at .8 and spikes up to 84.7

Post by mini-dunger »

hello again all

thanks for your help.

I purchased my ecu on the advice that it was plug and play for edis4.

none of the internal mods have been done.

So i ran the wire jumper wire today and it still runs the same. Still has a stumble at idle and an even worse stumble at WOT

i have changed plus up and down the heat range, closed plug gaps, opened plug gaps....

I thought I had it sorted and then it would die as if it was blowing the plugs out...

the miss seems to be only on 1 and 4 which are on the same bank of the coil..


oh man
mini-dunger
MS/Extra Newbie
Posts: 20
Joined: Tue Jul 04, 2017 2:39 am

Re: dwell stuck at .8 and spikes up to 84.7

Post by mini-dunger »

it also hunts really bad....
jsmcortina
Site Admin
Posts: 39587
Joined: Mon May 03, 2004 1:34 am
Location: Birmingham, UK
Contact:

Re: dwell stuck at .8 and spikes up to 84.7

Post by jsmcortina »

Hunting is often caused by being too lean at idle and with the fuel PW fluctuation. Add some fuel to that area (say in +5 steps) and see if that helps. I have found that adjusting cells to keep PW to a steady number helps too - this will mean that in the idle area, VE numbers go down as you move up the table.

James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk

My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
mini-dunger
MS/Extra Newbie
Posts: 20
Joined: Tue Jul 04, 2017 2:39 am

Re: dwell stuck at .8 and spikes up to 84.7

Post by mini-dunger »

thanks for your help mate..

I have included a photo of what I am trying to work with
Attachments
engine bay.jpg
engine bay.jpg (83.29 KiB) Viewed 527 times
racingmini_mtl
Super MS/Extra'er
Posts: 9128
Joined: Sun May 02, 2004 6:51 am
Location: Quebec, Canada
Contact:

Re: dwell stuck at .8 and spikes up to 84.7

Post by racingmini_mtl »

Where are you injecting? It's impossible to see in that picture and you don't mention it in your previous posts. You know that the siamese intake port setup on the Mini engine has some peculiarities when it comes to fuel injection, right? The fact you have trouble with the outer cylinders might be due to that and not ignition.

Jean
jbperf.com Main site . . . . . . . . . . . . . . . . . . . . . . jbperf.com Forum
Image
Post Reply