SR20 TAARKS Crank Wheel pattern
Moderators: jsmcortina, muythaibxr
SR20 TAARKS Crank Wheel pattern
Trying to get some help on how to set this up in MS3. Apparently it supports sequential on AEM,Haltech,FuelTech & MoTec. I am not seeing how to set this up in the MS3. This is the only wheel thats used and its on the CAM with no Crank Sensor
Heres the Manual for the part and gives instructions for Haltech,Link and FuelTech... Any Help would be appreciated.
https://www.efisolutions.com.au/assets/ ... 01v2-1.pdf
Heres the Manual for the part and gives instructions for Haltech,Link and FuelTech... Any Help would be appreciated.
https://www.efisolutions.com.au/assets/ ... 01v2-1.pdf
Re: SR20 TAARKS Crank Wheel pattern
Set it up as Toothed Wheel, then below set Trigger Wheel Arrangement to Dual Wheel, number of teeth = 12, Main Wheel Speed = cam, And every rotation of = Cam.
The man behind MS Labs
2005 Audi A3 2.0L TFSI DSG AWD - Extreme MS3
2002 Mazda Miata 1.8 6sp - Enhanced MS3 1.4.0, sequential injection, sequential ignition, big turbo, lots of boost
2005 Audi A3 2.0L TFSI DSG AWD - Extreme MS3
2002 Mazda Miata 1.8 6sp - Enhanced MS3 1.4.0, sequential injection, sequential ignition, big turbo, lots of boost
Re: SR20 TAARKS Crank Wheel pattern
Doesn’t duel wheel create a situation where it requires 2 inputs the crank input and cam input on a separate sensor? Or am I mistaken on that?Reverant wrote:Set it up as Toothed Wheel, then below set Trigger Wheel Arrangement to Dual Wheel, number of teeth = 12, Main Wheel Speed = cam, And every rotation of = Cam.
Sent from my iPad using Tapatalk
-
- Site Admin
- Posts: 39622
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: SR20 TAARKS Crank Wheel pattern
According to the manual you linked, the sensor provides two signals. "Home" will connect to the MS3 "cam" input.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: SR20 TAARKS Crank Wheel pattern
So if I understand correctly use main engine speed is cam as well as home on cam and they both read on the same single sensor?jsmcortina wrote:According to the manual you linked, the sensor provides two signals. "Home" will connect to the MS3 "cam" input.
James
Sent from my iPad using Tapatalk
-
- Super MS/Extra'er
- Posts: 17507
- Joined: Thu Apr 16, 2009 8:08 pm
Re: SR20 TAARKS Crank Wheel pattern
It looks like this has a north pole sensitive and south pole sensitive sensor in a common package, although I'm not 100% certain.
Matt Cramer -1966 Dodge Dart slant six running on MS3X
Re: SR20 TAARKS Crank Wheel pattern
I think so. I was just wondering if MS can run both Crank & Cam on the same single sensor. If so how would one configure? Main engine speed CAM and Wheel #2 is also CAM? Never set one up before.Matt Cramer wrote:It looks like this has a north pole sensitive and south pole sensitive sensor in a common package, although I'm not 100% certain.
-
- Site Admin
- Posts: 39622
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: SR20 TAARKS Crank Wheel pattern
The sensor has two signal wires. (Trigger and Home.) The ECU doesn't care that they are actually coming from the same sensor, it just wants two signals.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: SR20 TAARKS Crank Wheel pattern
Curious what settings ended up working for this? Currently working on the same issue. Thanks.