configuration error message
Moderator: LT401Vette
-
- MS/Extra Newbie
- Posts: 32
- Joined: Thu Jul 02, 2015 4:23 pm
configuration error message
Just installed my PNP microsquirt. Trying to create new project, after detecting microsquirt, Tunerstudio does not have configuration to support found firmware:unknown. Required serial signature 89.
Please click the other check box and browse to the ecu definition (ini) provided with your firmware. I am not sure how to fix this. I am new to microsquirt and tunerstudio. Help is appreciated.
Thanks,
Josh
Please click the other check box and browse to the ecu definition (ini) provided with your firmware. I am not sure how to fix this. I am new to microsquirt and tunerstudio. Help is appreciated.
Thanks,
Josh
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: configuration error message
That sounds like it is finding something else before your PNP. That isn't a proper PNP signature.Required serial signature 89.
Is anything else connected to the PC?
What baud is it detecting it at?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- MS/Extra Newbie
- Posts: 32
- Joined: Thu Jul 02, 2015 4:23 pm
Re: configuration error message
just tried again, baud rate is 115200. Yesterday baud was 9600. Stated this time required serial signature is 95. Nothing connected to laptop.
-
- MS/Extra Newbie
- Posts: 32
- Joined: Thu Jul 02, 2015 4:23 pm
Re: configuration error message
I tried to detect again and it states no controller found. Changed nothing.?
-
- MS/Extra Newbie
- Posts: 32
- Joined: Thu Jul 02, 2015 4:23 pm
Re: configuration error message
Sorry think I had power off last test. latest test found three: unknown firmware, USB, RTXT,RS232:87,83,15_ALL Baud 115200
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: configuration error message
Detecting 3 is actually fine... It is detecting 3 different drivers to use for connectivity and would use which ever you selected.
If you get nothing with powering off, it would seem as though you are talking to the right port. However, what you are getting back from the controller does not appear to be valid data.
Perhaps the firmware is corrupt?
Is it a PNP or a MicroSquirt?
Did you just purchase it?
If you get nothing with powering off, it would seem as though you are talking to the right port. However, what you are getting back from the controller does not appear to be valid data.
Perhaps the firmware is corrupt?
Is it a PNP or a MicroSquirt?
Did you just purchase it?
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- MS/Extra Newbie
- Posts: 32
- Joined: Thu Jul 02, 2015 4:23 pm
Re: configuration error message
I did just purchase. pnp microsquirt from an individual who has built many for others. how do I know firmware is corrupt?
-
- MS/Extra Newbie
- Posts: 32
- Joined: Thu Jul 02, 2015 4:23 pm
Re: configuration error message
I just tried to detect again... one driver...#89 firmware. Turned off, back on and got three, same #89, same port with different labels,RS232 ETC. What is my next step?
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: configuration error message
A number 89 is meaningless to TS and myself.
Try opening the port in Mini-Term at 115200 baud.
Type an Upper case S and Upper case Q in the top box, see if you get any meaningful response.
If you do not, it would seem there is something defective with the box. I would contact the person you purchased it from.
Try opening the port in Mini-Term at 115200 baud.
Type an Upper case S and Upper case Q in the top box, see if you get any meaningful response.
If you do not, it would seem there is something defective with the box. I would contact the person you purchased it from.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- MS/Extra Newbie
- Posts: 32
- Joined: Thu Jul 02, 2015 4:23 pm
Re: configuration error message
I typed in a capital S and Q and it just put a capital S and Q in bottom box. What kind of response should I expect?
Thanks
Thanks
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: configuration error message
You should get the serial signature of the controller and a string representing the firmware version.
With an MS2/MicroSquirt these would never be a single number, they would be String values.
With an MS2/MicroSquirt these would never be a single number, they would be String values.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Site Admin
- Posts: 39621
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: configuration error message
With a new item, your first place to look for support needs to be the supplier.fxbdydriver wrote:I did just purchase. pnp microsquirt from an individual who has built many for others. how do I know firmware is corrupt?
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".