Calibrate AFR not working?
Moderator: LT401Vette
-
- Super MS/Extra'er
- Posts: 1978
- Joined: Wed Apr 15, 2009 11:31 am
- Location: Oxford, PA
- Contact:
Calibrate AFR not working?
Posted this in my Beta thread but figured I'd toss it here too. Running the latest beta (2nd to most recent files posted) and I set Innovate LC1 default and write the table and while running it doesn't match my LC1/XD1 gauge, reads about 6pts rich or so.
I'm going to check things on the bench tonight or this morning for volts vs afr to see what's up on the stim.
I'm going to check things on the bench tonight or this morning for volts vs afr to see what's up on the stim.
-
- Site Admin
- Posts: 8230
- Joined: Thu Oct 14, 2004 12:48 pm
Re: Calibrate AFR not working?
It has never not worked for me. I would suspect a voltage offset.
Ken
Ken
Megasquirt is not for use on pollution controlled vehicles. Any advice I give is for off road use only.
-
- Super MS/Extra'er
- Posts: 1978
- Joined: Wed Apr 15, 2009 11:31 am
- Location: Oxford, PA
- Contact:
Re: Calibrate AFR not working?
Hm, I thought I did have it working at one point on an older code though. I will check the wiring in any case.
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Calibrate AFR not working?
Let me know what you see on the bench... That should be working fine. I will check it out on the latest firmwares.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Site Admin
- Posts: 8230
- Joined: Thu Oct 14, 2004 12:48 pm
Re: Calibrate AFR not working?
I just used it this morning with the CVS firmware with no issues.
Ken
Ken
Megasquirt is not for use on pollution controlled vehicles. Any advice I give is for off road use only.
-
- Super MS/Extra'er
- Posts: 1978
- Joined: Wed Apr 15, 2009 11:31 am
- Location: Oxford, PA
- Contact:
Re: Calibrate AFR not working?
Something is up.. looking at some logs I was idling around 12:1 on the older ones and reporting ~7:1 now with similar VE. I'll be sure to get on the bench with it tonight.
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: Calibrate AFR not working?
Check and see if you have similar pw and corrections to match the similar ve.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
-
- Super MS/Extra'er
- Posts: 1978
- Joined: Wed Apr 15, 2009 11:31 am
- Location: Oxford, PA
- Contact:
Re: Calibrate AFR not working?
Works totally fine on the stim. Not sure what's going on in the car. I'll try and toss it back in later today and do some checking. Maybe at some point the wire got grounded.
-
- Super MS/Extra'er
- Posts: 1978
- Joined: Wed Apr 15, 2009 11:31 am
- Location: Oxford, PA
- Contact:
Re: Calibrate AFR not working?
Got it, somehow my LC1 output 1 reset to narrowband after sitting. It's never the MS, never, even a new board with alpha code
-
- Site Admin
- Posts: 8230
- Joined: Thu Oct 14, 2004 12:48 pm
Re: Calibrate AFR not working?
Glad you found the issue then!
Ken
Ken
Megasquirt is not for use on pollution controlled vehicles. Any advice I give is for off road use only.
-
- Super MS/Extra'er
- Posts: 1978
- Joined: Wed Apr 15, 2009 11:31 am
- Location: Oxford, PA
- Contact:
Re: Calibrate AFR not working?
Yep rule #1 check the stupids.